- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- WAN Routing
- >
- HPE MSR3012 PPPOE Configuration Problem
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-02-2020 02:39 AM - last edited on тАО07-19-2020 08:55 AM by Parvez_Admin
тАО06-02-2020 02:39 AM - last edited on тАО07-19-2020 08:55 AM by Parvez_Admin
Cannot dial internet on MSR3012.
PPPOE Sessions is terminating with the following message.
<HPE MSR2>%Jun 2 17:10:00:306 2020 HPE MSR2 IFNET/3/PHY_UPDOWN: Physical state on the interface Virtual-Access0 changed to up.
%Jun 2 17:10:02:968 2020 HPE MSR2 IFNET/3/PHY_UPDOWN: Physical state on the interface Virtual-Access0 changed to down.
dialer-group 1 rule ip permit
<HPE MSR2>display current-configuration interface dialer 1
#
interface Dialer1
mtu 1492
ppp authentication-mode pap
ppp pap local-user abc password cipher abc
dialer bundle enable
dialer-group 1
dialer timer idle 0
dialer timer autodial 30
ip address ppp-negotiate
#
return
<HPE MSR2>
#
interface GigabitEthernet0/0
port link-mode route
combo enable copper
mac-address 4cae-a335-8905
pppoe-client dial-bundle-number 1
#
return
<HPE MSR2>
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-02-2020 11:05 AM
тАО06-02-2020 11:05 AM
Re: HP MSR3012 PPPOE Configuration Problem
Hi,
It seems that physical interface is flapping.
Is everyting fine on cabling side?
Could you please share software code running on the device?
Thanks!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-03-2020 12:29 AM
тАО06-03-2020 12:29 AM
Re: HP MSR3012 PPPOE Configuration Problem
Physical Cabling is fine. Following are further details.
<HPE MSR1>show version
HPE Comware Software, Version 7.1.059, Release 0306P30
Copyright (c) 2010-2016 Hewlett Packard Enterprise Development LP
HPE MSR3012 uptime is 0 weeks, 0 days, 0 hours, 33 minutes
Last reboot reason : User reboot
Boot image: cfa0:/msr3000-cmw710-boot-r0306p30.bin
Boot image version: 7.1.059P21, Release 0306P30
Compiled Jun 08 2016 16:00:00
System image: cfa0:/msr3000-cmw710-system-r0306p30.bin
System image version: 7.1.059, Release 0306P30
Compiled Jun 08 2016 16:00:00
Feature image(s) list:
cfa0:/msr3000-cmw710-security-r0306p30.bin, version: 7.1.059
Compiled Jun 08 2016 16:00:00
cfa0:/msr3000-cmw710-voice-r0306p30.bin, version: 7.1.059
Compiled Jun 08 2016 16:00:00
cfa0:/msr3000-cmw710-data-r0306p30.bin, version: 7.1.059
Compiled Jun 08 2016 16:00:00
CPU ID: 0x2
2G bytes DDR3 SDRAM Memory
8M bytes Flash Memory
PCB Version: 2.0
CPLD Version: 2.0
Basic BootWare Version: 1.60
Extended BootWare Version: 1.60
[SLOT 0]AUX (Hardware)2.0, (Driver)1.0, (CPLD)2.0
[SLOT 0]GE0/0 (Hardware)2.0, (Driver)1.0, (CPLD)2.0
[SLOT 0]GE0/1 (Hardware)2.0, (Driver)1.0, (CPLD)2.0
[SLOT 0]GE0/2 (Hardware)2.0, (Driver)1.0, (CPLD)2.0
[SLOT 0]CELLULAR0/0 (Hardware)2.0, (Driver)1.0, (CPLD)2.0
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-07-2020 02:19 PM
тАО06-07-2020 02:19 PM
SolutionHi,
Can you please remove below command from dialer interface then check:
undo ppp authentication-mode pap
If after removing this authentication-mode issue remains then perfrom the below steps and share the output:
undo t d
undo debugging all
debugging pppoe-client all interface
display int brief
debugging pppoe-client all interface GigabitEthernet0/0
debugging ppp all interface Dialer 1
terminal monitor
terminal debugging
ping -i Dialer 1 <server IP doing authentication>
undo debugging all
undo terminal monitor
undo terminal debugging
Thanks!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-11-2020 06:34 AM
тАО06-11-2020 06:34 AM
Re: HP MSR3012 PPPOE Configuration Problem
Thanks.
undo ppp authentication-mode pap
This solved the problem.