HPE 9000 and HPE e3000 Servers
1755655 Members
2639 Online
108837 Solutions
New Discussion юеВ

Re: GSP Error in rp5470 server

 
SOLVED
Go to solution
Binukuttan VM_1
Frequent Advisor

GSP Error in rp5470 server

Dear Sir,

I am facing an intermitent fan failure GSP error in rp 5470 server.But I found always all 6 fans( 4 fans on side+2 fans on front and rear) working fine- without any fault led indications and rotaing fine.

I run STM selecting system - i am attaching the output of information log .....



cabinet in the system and the Field Replaceable Unit Identification Data

Units on the system. Each entry can be accessed by the prev/next key in the







Hardware Information for Cabinet 0



Hardware Inventory:

Cabinet Fans = 8 (1 Failure; Fan 6)

Cabinet Power Supplies = 2 (No Failures)

Cabinet I/O Bay Fans = 0

I/O Bay Power Supplies = 0



Hardware Locations:

Hardware Component Map (locations 00-31)

-----------------------------------------------------------------

|0|0|0|0|0|0|0|0|0|0|1|1|1|1|1|1|1|1|1|1|2|2|2|2|2|2|2|2|2|2|3|3|

|0|1|2|3|4|5|6|7|8|9|0|1|2|3|4|5|6|7|8|9|0|1|2|3|4|5|6|7|8|9|0|1|

|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|-|

cf |p|p|p|p|p|p|F|p| | | | | | | | | | | | | | | | | | | | | | | | |

cps|p| |p| | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

-----------------------------------------------------------------

cf - Cabinet Fan (blower)

cps - Cabinet Power Supply

p - Component present at the marked location.

F - Component failed at the marked location.



Miscellaneous Cabinet Information:

Platform Specific Cabinet Information = 0x0


-----------------------------------------------------------------------------------------



STM Information logs on system says there are 8 Cabinet Blower Fans, out of that fan 6 is failed. If i take Fan IDs in server , there are Fan 0,Fan 1( both are front and rear fans),Fan 2,Fan 3,Fan 4 and Fan5( All 4 are fans on side).

I am not able to find - 8 No. of Cabinet Blower Fans as told in STM.


Please advice ..Thanks in advance

regds
Binu


5 REPLIES 5
RAC_1
Honored Contributor

Re: GSP Error in rp5470 server

stty -queryGSP /dev/diagx
stty +resetGSP /dev/diagx

Alo, may be you need to look at GSP firmware update.
There is no substitute to HARDWORK
Joerg-Udo Werner
Frequent Advisor
Solution

Re: GSP Error in rp5470 server

Hello Binu,
Let me give you a short list of the fans inside the rx5670. You have two additional fans at the rear of the system called "Power Converter Fans".


Here is the list:
FAN 9 -> Front Fan
FAN 1 -> Rear Fan
FAN 2 -> PCI Cardcage FAN (upper left)
FAN 3 -> PCI Cardcage FAN (upper right)
FAN 4 -> PCI Cardcage FAN (lower left)
FAN 5 -> PCI Cardcage FAN (lower right)
FAN 6 -> Power Converter FAN (right) -> your problem
FAN 7 -> Power Converter FAN (left)

Hope this helps,
Udo
Binukuttan VM_1
Frequent Advisor

Re: GSP Error in rp5470 server

Dear sir,

Can you pls tell me the locaion of power convertor fan.Is it located in rear side of server or in inside the cabinet.From which side it will be visible..

regds
binu
Joerg-Udo Werner
Frequent Advisor

Re: GSP Error in rp5470 server

They are visible from the rear! The fans are just under the big rear fan. Try to find the power cords and go 5cm to the left and you will see the two fans. These fans also have a LED.

Regards,
Udo
Binukuttan VM_1
Frequent Advisor

Re: GSP Error in rp5470 server

thanks