- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- LAN Routing
- >
- Re: Inter VLAN routing
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-16-2014 10:08 AM
тАО12-16-2014 10:08 AM
I'm having a fairly frustrating time trying to get a 2920-24G switch to perform basic inter-VLAN routing. I have wiped the config, and updated it to the latest firmware, and started again, setting up 2 VLANs. My laptop is connected to port 20 (VLAN 80) and another machine is connected to port 10 (VLAN 70). Both have IPs in the respective subnets and both can ping each other if connected to the same VLAN and subnet (so it's not a firewall issue on the machines). The second machine also has a web page that I can access from the same VLAN but not accross VLANs. I can ping both hosts from the switch.
The current switch config is as follows:
sh run
Running configuration:
; J9726A Configuration Editor; Created on release #WB.15.16.0005
; Ver #06:0c.fc.f3.ff.35.0d:c2
hostname "ZAO-CORE-SW"
module 1 type j9726a
trunk 23-24 trk1 trunk
ip default-gateway 10.80.65.254
ip ttl 60
ip route 0.0.0.0 0.0.0.0 10.80.65.254
ip routing
snmp-server community "public" unrestricted
snmpv3 enable
snmpv3 restricted-access
snmpv3 user "initial"
snmpv3 user "mmradmin"
oobm
ip address dhcp-bootp
exit
vlan 1
name "DEFAULT_VLAN"
no untagged 1-22
untagged A1-A2,B1-B2,Trk1
ip address 192.168.65.1 255.255.255.0
ip igmp
exit
vlan 70
name "Workstation_Network"
untagged 1-18
tagged Trk1
ip address 10.70.65.1 255.255.255.0
ip helper-address 10.80.65.10
ip igmp
exit
vlan 80
name "Server_Network"
untagged 19-22
tagged Trk1
ip address 10.80.65.1 255.255.255.0
ip helper-address 10.80.65.10
ip igmp
exit
primary-vlan 80
spanning-tree
spanning-tree Trk1 priority 4
The trunk in the above config goes to a 2530-24G layer 2 switch - but I've tried without having that in the config and it made no difference - so I'm fairly sure it has no effect either way. I'm starting to lose my rag, as I've tried almost everything I can think of, and spent a day looking through web sites and product documentation, and I can't find an example config to follow that actually works. I've tried without a primary VLAN and without IGMP.
Thanks in advance for any help.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-16-2014 10:18 AM
тАО12-16-2014 10:18 AM
Re: Inter VLAN routing
I should also mention that my laptop has a default gateway set to 10.80.65.1 and the other machine has 10.70.65.1 as its gateway. It's unfortunately not that obvious.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-16-2014 07:19 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-14-2015 03:04 PM
тАО02-14-2015 03:04 PM
Re: Inter VLAN routing
I'm not familiar with configuring routing on the 2920-24G; however, I have worked with 3500-24 layer 3 switches. You may have missed a configuration parameter. When I configure IP RIP V2 on the 3500's, after the 'ip routing' command, I have to add a 'router rip' command and then enable.
So it looks like this:
Procurve# config t
Procurve (config)# ip routing
Procurve (config)# router rip
Procurve (rip)# enable
Procurve (rip)# exit
Procurve (config)# wr mem
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2015 01:50 PM
тАО02-23-2015 01:50 PM
Re: Inter VLAN routing
Sorry for such a belated reply - but embarrassingly it seems you were correct. I came back the following day with a diffferent machine, and was able to get packets between all the subnets / VLANs. I've since had to configure a number of other HP switches, using a similar config, and had no issues at all. It was just one of those days, I guess.