- Community Home
- >
- Networking
- >
- Wireless
- >
- M and MSM Series
- >
- Re: Antenna Radio Pattern MSM430
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-31-2012 06:23 AM
тАО10-31-2012 06:23 AM
Hello,
we are about to install a couple MSM430 but I couldn't find the antenna radio pattern of the omnidirectional antennas the AP has inside.
We don't know how the antennae are oriented, do the antenna emit horizontally and vertically, taken by reference the AP lying on the floor? Should we install them on the ceiling or on the wall?
Kind regards,
Aar├│n
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-09-2012 02:54 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-28-2017 03:38 AM
тАО09-28-2017 03:38 AM
Re: Antenna Radio Pattern MSM430
@Arimo wrote:Hi
The antenna pattern is practically a ball. The APs are plenum rated, you can do it either way.
Hey,
does the same apply for the MSM460?
Thanks,
Ascendor
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-28-2017 11:05 PM
тАО09-28-2017 11:05 PM
Re: Antenna Radio Pattern MSM430
Hi All,
From experience, the MSM460/560 signal is closer to the infinity sign (sideways figure 8), with very little signal to the rear (mount side). The top part (with ligths) has less signal range than the sides as well.
I have not been able to wall mount them due to this fact.
We have 496x MSM460/560 APs currently. (And one MSM430 ;-D)
Regards,
Craig
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-01-2017 11:44 PM
тАО10-01-2017 11:44 PM
Re: Antenna Radio Pattern MSM430
@CraigS1971 wrote:Hi All,
From experience, the MSM460/560 signal is closer to the infinity sign (sideways figure 8), with very little signal to the rear (mount side). The top part (with ligths) has less signal range than the sides as well.
I have not been able to wall mount them due to this fact.
We have 496x MSM460/560 APs currently. (And one MSM430 ;-D)
Regards,
Craig
Thanks @CraigS1971!
I'd also like some official response though. The manual doesn't state anything (and explicitly describes wall-mount procedure), so in theory it should be fine to mount them on the wall - but I too have a feeling that they are not covering the area well then.
@Arimo, can you say something about this?