- Community Home
- >
- Storage
- >
- Legacy
- >
- Network Attached Storage (NAS) - Enterprise
- >
- Re: AIO600 and iSCSI acceleration setup?
Network Attached Storage (NAS) - Enterprise
1755230
Members
5163
Online
108831
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-05-2007 08:27 PM
тАО04-05-2007 08:27 PM
Hello, I have problems setting up the acceleration on the embedded NIC of AiO600. The Acceleration Pack license installed OK, created the iSCSI device (I can see it both in the NCU and SCSI adapters), I can ping the IP address set to the iSCSI accelerated device from the client, but the iSCSI target software does not show the device as network interface (when I open S iSCSI target, right click on the target, Properties, I have just the "non-accelerated" NIC IP address there - so the accelerated device's IP is not responding to iSCSI requests.
I have been trying to find the acceleration setup for AiO in the documentation but failed...
any help or thought highly appreciated, thanks.
Vladimir
I have been trying to find the acceleration setup for AiO in the documentation but failed...
any help or thought highly appreciated, thanks.
Vladimir
Solved! Go to Solution.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-11-2009 11:33 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2009 03:52 AM
тАО10-12-2009 03:52 AM
Re: AIO600 and iSCSI acceleration setup?
hello,
I forgot to close the thread, it is pretty old - but You are right. the acceleration works for initiator side only. regards, V.
I forgot to close the thread, it is pretty old - but You are right. the acceleration works for initiator side only. regards, V.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2009 03:53 AM
тАО10-12-2009 03:53 AM
Re: AIO600 and iSCSI acceleration setup?
thread closed
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP