- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Error while doing a remote execution in OpenVMS IA...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2007 07:30 PM
тАО03-20-2007 07:30 PM
But whenever i tried to connect to this VMS machine remotely, the rexec facility(used in client) pops up with an error "Bad Address Definition". its my application that is throwing this error.it shows the bad address as "10.xx.xxx.xxx/2040"(port number specified)
For performing this remote execution, it need to have a proxy enabled in the UCX for the client windows machine.i have created this by doing the following:
$ucx
TCPIP>add proxy vms-username/REMOTE_USER="MYuserName" /HOST=MYhostName
These information are needed for the remote execution.
hostname:
username:
password:
command to invoke the application:
TCP/IP Port Number:(default value is 2040)
Server Start Timeout:(default value is 60)
i don't know why its showing this as a bad address. i doubt whether this port number has something to do with this error or whether i made some mistake in defining the proxy in TCP/IP.
Appreciate if anyone could comment on this.
Manesh
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2007 08:21 PM
тАО03-20-2007 08:21 PM
Re: Error while doing a remote execution in OpenVMS IA64
Try to do a tcptrace/fu to find what communication takes place.
Try tpo use a * in the host part of the proxy setup.
Wim
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2007 08:21 PM
тАО03-20-2007 08:21 PM
Re: Error while doing a remote execution in OpenVMS IA64
to start with:
WELCOME to the VMS Forum!
The first thing to check is the resolving of MyhostName (DNS or local host table).
What does
$ UCX ping MyhostName
give?
Proost.
Have one on me.
jpe
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2007 08:34 PM
тАО03-20-2007 08:34 PM
Re: Error while doing a remote execution in OpenVMS IA64
"System detected an address which was not valid while attempting to access the address parameters.".
What did you exactly specify ?
Wim
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2007 08:52 PM
тАО03-20-2007 08:52 PM
Re: Error while doing a remote execution in OpenVMS IA64
Wim,
Thanks for ur reply.
My application client asks for the username/passwd.
This is what i did to create the Proxy.
>add proxy shodgin/remote_user="msasanka"/host=10.60.254.190
(this is the ip of my workstation).
exact information specified:
hostname: 10.60.255.37
username: shodgin
password: ********
command to invoke the application: RS1
TCP/IP Port Number:2040
Server Start Timeout:60
JPE,
Thanks for ur reply.
$UCX ping 10.60.254.190
gives 4 packets transmitted & 4 packet received.
Thanks
/Manesh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2007 09:08 PM
тАО03-20-2007 09:08 PM
SolutionHP recommends that you define host names and aliases to use proxy facilities.
You need define "MYuserName" on TCP/ip services
using:
TCPIP>set host "MYuserName"/addres=your_ip/alias=MYuserName
Saludos.
Daniel.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2007 09:23 PM
тАО03-20-2007 09:23 PM
Re: Error while doing a remote execution in OpenVMS IA64
Thanks a ton for ur reply.
It worked. i defined my hostname & then added the proxy entry with my hostname. and guess what, my application client is able to connect to the server.
Thanks a lot. :-)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2007 10:41 PM
тАО03-20-2007 10:41 PM
Re: Error while doing a remote execution in OpenVMS IA64
I hope you mean MYhostName ?
Manesh,
How did you define the proxy if you didn't set up MYhostName ?
Wim
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2007 11:10 PM
тАО03-20-2007 11:10 PM
Re: Error while doing a remote execution in OpenVMS IA64
tcpip> set host xxxx/address=10.60.254.190/alias=xxxx
tcpip> add proxy shodgin/remote_node="xyxy"/host=xxx
thanks to all..
:-)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-20-2007 11:10 PM
тАО03-20-2007 11:10 PM
Re: Error while doing a remote execution in OpenVMS IA64
tcpip> set host xxxx/address=10.60.254.190/alias=xxxx
tcpip> add proxy shodgin/remote_node="xyxy"/host=xxxx
thanks to all..
:-)