- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: Need set host/mop syntax for MAC address
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-18-2004 02:18 AM
тАО10-18-2004 02:18 AM
Chaim
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-18-2004 02:36 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-18-2004 02:37 AM
тАО10-18-2004 02:37 AM
Re: Need set host/mop syntax for MAC address
$ set host/mop -
_$ /circuit = circuit-name - (1)
_$ /address = lan-address - (2)
_$ /verification = octet-string - (3)
_$ /disconnect = disconnect-character -
_$ /break = break-character
1. Specifies the name of the MOP circuit over which the target system can be reached.
2. Specifies the LAN hardware address associated with this client.
3. Specifies the verification string. The value is an octet string of up to 16 hexadecimal digits. Enter the value as "%X" followed by an even number of digits. For more information about specifying a verification string, see Section 10.2.2.1. The default is %X0000000000000000.
Purely Personal Opinion
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-18-2004 12:08 PM
тАО10-18-2004 12:08 PM
Re: Need set host/mop syntax for MAC address
If using DECnet Phase V, then to make permanent change try using
$net$configure
option 8 - Configure MOP Client database
this will edit the file SYS$MANAGER:NET$MOP_CLIENT_STARTUP.NCL;
So you can just $set host/mop
without the need to remember the MAC address, etc.. all the time
Content of file would look something like
CREATE MOP CLIENT SERV01
SET MOP CLIENT SERV01 CIRCUIT = CSMACD-0 -
,ADDRESSES = {08-00-2B-B1-9B-00} -
,PHASE IV HOST ADDRESS = 2.1 -
,PHASE IV CLIENT NAME = SERV01 -
,DUMP FILE = {SYS$SYSROOT:
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-18-2004 07:49 PM
тАО10-18-2004 07:49 PM
Re: Need set host/mop syntax for MAC address
/ADDRESS=mac_address
/DISCON=D means use Control and D to disconnect
CIRCUIT=CSMACD-0 is the circuit we use.
Hopefully this will help.
Yours Terry.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-18-2004 07:59 PM
тАО10-18-2004 07:59 PM
Re: Need set host/mop syntax for MAC address
I was able to connect to the terminal server and then get the server name etc etc.
Chaim