- Community Home
- >
- Storage
- >
- Legacy
- >
- Storage Software
- >
- Re: Command View Connection
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-23-2009 10:37 AM - last edited on тАО03-10-2014 10:49 PM by Maiko-I
тАО09-23-2009 10:37 AM - last edited on тАО03-10-2014 10:49 PM by Maiko-I
Hi,
i have some troubles with Command View connections to 2 EVA4400's, and i think i have already seen the resolution somewhere here.
This is a Continous Access config on two remote rooms separated with about 200 meters :
- room A with 2 Brocade v6.2.1, EVA4400 v9.006 and a ManApp with Command View 9.1
- room B with 2 Brocade v6.2.1, EVA4400 v9.522 and a ManApp with Command View 9.1
Each ManApp sees without problem its near EVA4400, but there is connection problem with the coresponding remote EVA4400 :
- no seen, or
- seen with the follwing message in GUI :
"Blocked HSV300 V09 Storage System ***Managed by another agent***
With SSSU, the message is :
Error : error storage cell is managed by another agent : ManagementAgentName : 'Name of Remote ManApp' ManagementAgentIP : 'IP of RemoteManApp'
This behavior is the same with the remote Command View service stopped.
Is there a command to unlock the Command View connection ?
Jean-Pierre
P.S. This thread has eben moevd from Disk Array to HP Storage System Scripting Utility (SSSU). - Hp Forum Moderator
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-23-2009 12:20 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-24-2009 02:24 AM
тАО09-24-2009 02:24 AM
Re: Command View Connection
it's a long story.
The first time the SSSU command 'set system EVA2 manage' gives an error.
So the paths seen by cvutil have marked 'non valid' or 'not responsive'.
Reboot the ManApp1 and the Controller 1 of EVA2, and the paths become valid.
Then, the EVA2 was not seen from ManApp1, i do the SSSU command 'refresh' and the EVA2 appears.
And after, i do a SSSU command 'set system EVA2 manage' again and the connexion to EVA2 is OK.
The same think on room B does not give the same result, the 'refresh' or 'rediscover' command is not able to show EVA1.
I will try when upgrade to 9.522 will be made
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-24-2009 09:46 PM
тАО09-24-2009 09:46 PM