- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: Pairdisplay intermittent
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-02-2010 10:13 AM
тАО11-02-2010 10:13 AM
Pairdisplay intermittent
C:\HORCM\etc>pairdisplay -g BCDR_CA -I50
pairdisplay: [EX_ENORMT] No remote host alive for remote commands or Remote Raid
Manager might be blocked (sleeping) on an existing I/O.
Refer to the command log(C:\HORCM\log50\horcc_G4W2878C_log.txt) for details.
Then I run it on the other one and it works, but then it all of a sudden works on the other... this works this way going both directions... then I let it sit for a couple of minutes, then it does not work again... I tried adjusting the timeout in the HORCM.conf file....I have checked the network... there are no firewalls and all looks good. Is there some setting that will set a "keep alive" value where they do not "sleep"
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-02-2010 10:13 PM
тАО11-02-2010 10:13 PM
Re: Pairdisplay intermittent
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-03-2010 06:04 AM
тАО11-03-2010 06:04 AM
Re: Pairdisplay intermittent
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-25-2012 07:16 AM
тАО07-25-2012 07:16 AM
Re: Pairdisplay intermittent
Hello,
I write you this message because i have exactly the same problem with Raid Manager on a linux.
Do you success to resolve your problem?
Thanks for you Help.
Regards,
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-03-2013 02:50 AM
тАО12-03-2013 02:50 AM
Re: Pairdisplay intermittent
I have exactly the same problem with Raid Manager / CCI 1-30-3.3 on windows 2008. I came to the conclusion the horcminstances go to sleep after 60 seconds from the last time they were used. They will not wake up when a request over the network comes, but they will when they are used with a pairdisplay command locally. So, if you run pairdisplay on both servers, the one on which you issued the first pairdisplay will time-out and the one you issued the command a second later will work. If you go again to the first server and issue again a pairdisplay in less than 60 sec. from the first one, it will work also. As workarounds some people a runing a pairvolcheck command every 45 sec to prevent services from going to sleep, other people are running it as a Windows service (there is a tutorial available if you search for HORCM and SRM)