Skip to ContentSkip to Footer
Start of content
- Community Home
- >
- Servers and Operating Systems
- >
- BladeSystem
- >
- BladeSystem - General
- >
- Pass-Thru Module Problem!!
BladeSystem - General
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-04-2010 06:30 AM
09-04-2010 06:30 AM
Pass-Thru Module Problem!!
When I attach Pass-Thru Module to Interconnect bay #5 at c7000, it goes to flashing amber and green mode indicating that there is a port mismatch!
is it due to using the Chelsio 10G Ethernet Mezzanine?
is it due to using the Chelsio 10G Ethernet Mezzanine?
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-05-2010 10:50 PM
09-05-2010 10:50 PM
Re: Pass-Thru Module Problem!!
which mezzanine slot have you inserted the ethernet mezzanine card on? If your ethernet pass through module is in interconnect bay 5, then the ethernet mezz card should be in mezz slot 2.
Please refer to the section "Mapping to interconnect ports" for more information on port mapping in C7000 enclosure.
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00698534/c00698534.pdf
Regards,
Clarete
Please refer to the section "Mapping to interconnect ports" for more information on port mapping in C7000 enclosure.
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00698534/c00698534.pdf
Regards,
Clarete
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-11-2010 11:42 PM
09-11-2010 11:42 PM
Re: Pass-Thru Module Problem!!
Yes it is @ Mezzanine Slot 2. I think that our card interface is XAUI while Passthru uses 10GBASE-KR.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
End of content
United States
Hewlett Packard Enterprise International
Communities
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP