how to set password protection on a router
Posted to: Security e-Series
2 weeks ago how to set password protection on a router (brute-force attack)Spoiler (Highlight to read)%@3540504%Aug 9 15:30:21:177 2019 msr2003 SSHS/6/SSHS_DISCONNECT: SSH user admin (IP: 193.32.163.123) dis ...
NTA settings gone after IMC upgrade
Posted to: IMC
2 weeks ago are NTA settings something that shold be backed up during DB backup. I've noticed While upgrading to 7.3e0703 no NTA configuration exist on the new server
Compatibility Aruba 10GBASE-T SFP+ RJ45 and HP 12500 and HP5820
Posted to: Switching and Routing
2 weeks ago IĀ“d like to know if Aruba 10GBASE-T SFP+ RJ45 transceiver JL563A can be used over the switches HP 12500 and HP 5820.Tks
How to autobackup 3 com hp switch config and send it using ftp/tf ...
Posted to: Switches, Hubs, and Modems
2 weeks ago
How to autobackup 3 com hp switch config and send it using ftp/tf ...
Posted to: Comware Based
2 weeks ago HelloI need to create and send to tftp/ftp configuration backup of hp switch every day. There are built-in functions for it in Cisco/Dlink, are there any ways to do it in hp?
Command to not generate message when an interrface goes up or dow ...
Posted to: Aruba & ProVision-based
2 weeks ago Hi,Does anybody know if there is a command that can be used to not generate a message (syslog and SNMP trap) when a specific interrface goes up or down on an ArubaOS (fka ProVision)-based Network ...
HPE 5920 full flash / Saving configuration failed due to lack of ...
Posted to: Comware Based
2 weeks ago my flash is full and i do not know how to resolve this issue.no sure what i can delete safley and ehat the correct command is.below id a dir /all of the flash.this is for a HP 5920any help hreatl ...
Configure HPE 1920 L3 with Dell Powerconnect 2724 VLANs
Posted to: Aruba & ProVision-based
2 weeks ago Greetings everyone,Iāve just bought an HPE 1920 L3 switch that it will be used to route traffic from L2 switch using specific VLAN Tags. I could just use my L3 switch to setup my VLANs and plug t ...
Aruba 2540 Certificate Error Post Reconfiguration
Posted to: Aruba & ProVision-based
2 weeks ago All,I am trying to reconfigure a previously configured Aruba 2540. I am trying to enable https using a self signed certificate. Post config I get a certificate error in the browser. I have tried ...
how set authorized mac address by SNMPSET
Posted to: Switching and Routing
2 weeks ago
how set authorized mac address by SNMPSET
Posted to: Aruba & ProVision-based
2 weeks ago Dear all,I have a switch HP J9775A 2530-48G and I would like to set a port on security mode through SNMP.I found this MIB for setting max mac count on port 71.3.6.1.4.1.11.2.14.2.10.3.1.3.1. ...
euplat jserver and other services can't start after upgrade t ...
Posted to: IMC
2 weeks ago Hi All After upgrading from 7.3 E0605 to 7.3 E0703 there are 4 processes that won't start, anyone faced this issue?
NTP problem with a JG963A
Posted to: Comware Based
2 weeks ago Hi,Currently, I'm trying to synchronize our JG963A with our firewall for NTP.In the config, when I choose " Automatically synchronize the clock with a trusted time source on the network", I can s ...
configure ipsec vpn cisco881 and msr2003 not work (
Posted to: Security e-Series
2 weeks ago
configure ipsec vpn cisco881 and msr2003 not work (
Posted to: Comware Based
2 weeks ago Cannot configure ipsec vpn between cisco881 and msr2003I ask for helpPhase 1 works, and then no:cisco800#sh crypto isakmp sa IPv4 Crypto ISAKMP SA dst ...
hpe msr2003 how to enable encryption-algorithm aes
Posted to: Comware Based
2 weeks ago I have a msr2003 hpe router and I need to enable encryption-algorithm aesTell me how to do it?Now only DES is available to me[msr2003-ipsec-transform-set-test]esp encryption-algorithm ?des-cbc 56 ...
HP Procurve 2160-24 Bottlenecking speed to 100Mbps
Posted to: LAN Routing
2 weeks ago Hi Guys,Was wondering if you might be able to help me. We recently changed Internet Service Providers and have upped our service from 100Mbps up and download to 200Mbps up and download and it see ...
how should I configure sflow sampling?
Posted to: Switches, Hubs, and Modems
2 weeks ago I'm reading the sflow section here:https://support.hpe.com/hpsc/doc/public/display?docLocale=en_US&docId=emr_na-a00040098en_usto configure sflow in order to reach ManageEngine netflow analyze ...
HPE FlexFabric 10Gb 2-port 534FLR-SFP+ Adapter - Cisco Meraki MS4 ...
Posted to: Comware Based
2 weeks ago Dear Everyone, I'm going to provide two servers connected to a shared SAN, but the end customer already has in-site a stack made of two Cisco Meraki MS425-16, so he wouldn't want to buy ...
Error applying GTS on HP 1920-48g
Posted to: Switching and Routing
2 weeks ago
Error applying GTS on HP 1920-48g
Posted to: Web and Unmanaged
2 weeks ago Hi, I wanted to limit the bandwidth in a 1920-48g swicht in a port, but when applying the policy I get an error, it indicates Setting GigabitEthernet1 / 0/5 - Not support match any.The configurat ...
HPE FlexNetwork 5130 HI Switch Series - management port
Posted to: Switches, Hubs, and Modems
2 weeks ago
HPE FlexNetwork 5130 HI Switch Series - management port
Posted to: Comware Based
2 weeks ago Hi,I need to configure the static IP settings of the management port of a 5130 switch.I don't have the switch in hand yet, so I checked several HPE user guides for the HPE FlexNetwork 5130 H ...
IRF on JH149A
Posted to: Comware Based
2 weeks ago Dear All,We recently upgraded L3 Switch to (HPE 5510 24G SFP 4SFP+ HI 1-slot Switch JH149A) and configured two switches through IRF.Need some help how the secondary Switch access on Web. Primary ...
3800 stack routing fails if a certain member is off line
Posted to: LAN Routing
2 weeks ago Hi, We have a pair of stacked 3800's connected to a pair of stacked 2920's. We have inter vlan routing enabled with a different subnet on the 2920's. This has been up an ru ...
