- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: Starting a detached process from the batch que...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-24-2005 04:03 AM
тАО08-24-2005 04:03 AM
Re: Starting a detached process from the batch queue
A big thankyou to all who contributed to solve my problem!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-24-2005 04:08 AM
тАО08-24-2005 04:08 AM
Re: Starting a detached process from the batch queue
are you sure in interactive mode, can your command works?
The difference between interactive mode and batch mode are:
1) SYLOGIN and LOGIN: statements submitted by F$MODE()
2) Rarely access restricion on SYSUAF
May be you have limited MAXDETACH in your SYSUAF, but this value is valid either in interactive either in batch mode.
I guess you have some limited quota.
Do you have process dump?
Antonio Vigliotti
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-24-2005 04:41 PM
тАО08-24-2005 04:41 PM
Re: Starting a detached process from the batch queue
Some DCL commands have different defaults for qualifiers depending on the mode, e.g. the lINK commands automagially adds a /MAP if run in batch, which leads to an error if you try to install VMSINSTALlable kits in batch, because VMSINSTAL sets default to MISSING:[MISSING], which makes the creation of a MAP-file quite difficult. There were some softwarekits I had to reassemble.
regards Kalle
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-24-2005 05:08 PM
тАО08-24-2005 05:08 PM
Re: Starting a detached process from the batch queue
Welcome to the ITRC forum Peter.
Good to read your problem is addressed.
You can express you gratitude in measured steps by assigning points to answers.
You can gracefully indicate that you are no longer interested in further discussion on this topic by 'closing' it.
Regards,
Hein. (0 point for this comment please).
http://forums1.itrc.hp.com/service/forums/helptips.do?#28
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-24-2005 05:40 PM
тАО08-24-2005 05:40 PM
Re: Starting a detached process from the batch queue
Once again, thanks to all who contributed to the forum.
- « Previous
-
- 1
- 2
- Next »