- Community Home
- >
- Servers and Operating Systems
- >
- ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- cannot replace failed frive
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-20-2014 11:43 AM
02-20-2014 11:43 AM
cannot replace failed frive
I am facing the following situation were rebuild is not starting. what should I do?
the unassigned drive (2I:1:1) is in the same slot as the failed drive (1I:1:1) but with different name.
starlnx1:~# hpacucli ctrl slot=1 show config detail
Smart Array P400 in Slot 1
Bus Interface: PCI
Slot: 1
Serial Number: PA2240J9SU038D
Cache Serial Number: PA82C0D9STZ5QY
RAID 6 (ADG) Status: Enabled
Controller Status: OK
Hardware Revision: B
Firmware Version: 7.22
Rebuild Priority: Medium
Expand Priority: Medium
Surface Scan Delay: 15 secs
Surface Scan Mode: Idle
Wait for Cache Room: Disabled
Surface Analysis Inconsistency Notification: Disabled
Post Prompt Timeout: 0 secs
Cache Board Present: True
Cache Status: Temporarily Disabled
Cache Status Details: Cache disabled; requires reboot to enable cache.
Cache Ratio: 25% Read / 75% Write
Drive Write Cache: Disabled
Total Cache Size: 256 MB
Total Cache Memory Available: 208 MB
No-Battery Write Cache: Disabled
Cache Backup Power Source: Batteries
Battery/Capacitor Count: 1
Battery/Capacitor Status: OK
SATA NCQ Supported: False
Array: A
Interface Type: SAS
Unused Space: 0 MB
Status: Failed Physical Drive
Array Type: Data
One of the drives on this array have failed or has been removed.
Logical Drive: 1
Size: 279.4 GB
Fault Tolerance: RAID 1
Heads: 255
Sectors Per Track: 32
Cylinders: 65535
Strip Size: 128 KB
Full Stripe Size: 128 KB
Status: Interim Recovery Mode
Caching: Enabled
Unique Identifier: 600508B1001030364130433244300500
Disk Name: /dev/cciss/c0d0
Mount Points: / 14.0 GB, none 5.6 GB, /VM 149.0 GB, /NETWORK 110.8 GB
OS Status: LOCKED
Logical Drive Label: A00008105001438006A0C2D062A9
Mirror Group 0:
physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 0 MB, Failed)
Mirror Group 1:
physicaldrive 2I:1:2 (port 2I:box 1:bay 2, SAS, 300 GB, OK)
Drive Type: Data
physicaldrive 1I:1:1
Port: 1I
Box: 1
Bay: 1
Status: Failed
Last Failure Reason: No failure
Drive Type: Data Drive
Interface Type: SAS
Size: 0 MB
physicaldrive 2I:1:2
Port: 2I
Box: 1
Bay: 2
Status: OK
Drive Type: Data Drive
Interface Type: SAS
Size: 300 GB
Rotational Speed: 10000
Firmware Revision: HPD9
Serial Number: KLHTETKF
Model: HP EG0300FBVFL
Current Temperature (C): 32
Maximum Temperature (C): 39
PHY Count: 2
PHY Transfer Rate: Unknown, Unknown
unassigned
physicaldrive 2I:1:1
Port: 2I
Box: 1
Bay: 1
Status: OK
Drive Type: Unassigned Drive
Interface Type: SAS
Size: 300 GB
Rotational Speed: 10500
Firmware Revision: HPD0
Serial Number: Z320A184FTM91349
Model: HP EG0300FCSPH
Current Temperature (C): 31
Maximum Temperature (C): 35
PHY Count: 2
PHY Transfer Rate: Unknown, Unknown
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-20-2014 12:00 PM
02-20-2014 12:00 PM
Re: cannot replace failed frive
Hello :)
You need to assign physicaldrive 2I:1:1 as spare for that array
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-20-2014 12:12 PM
02-20-2014 12:12 PM
Re: cannot replace failed frive
I can't:
starlnx1:~# hpacucli ctrl slot=1 array A add spares=2I:1:1
Error: This operation is not supported with the current configuration. Use the
"show" command on devices to show additional details about the
configuration.
Reason: Array is transforming
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-20-2014 12:25 PM
02-20-2014 12:25 PM
Re: cannot replace failed frive
Backup server data
Shutdown server
Replace failed drive with unassigned drive
Power on server and observe dialogs and prompt from P400 controller
(there might be a rebuild/repair ... can't remember exactly for P400 but here:
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-20-2014 12:29 PM
02-20-2014 12:29 PM
Re: cannot replace failed frive
I will try that. I have tryied so many things on this array that I am not sure if I have already done it.
I will let you know ...
regards
Kostis.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-23-2014 04:12 AM
02-23-2014 04:12 AM
Re: cannot replace failed frive
reboot didn't work.
no "F1" or "F2" prompt on boot except that P400 reports that one drive (with the wrong ID) needs to be replaced.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-23-2014 11:48 PM
02-23-2014 11:48 PM
Re: cannot replace failed frive
Please read the manual in the link provided in my previous post
There you will find the manual for that controller
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP