Switching and Routing Networking Forum

Hello everyone, i need some information about how to disable L3 on HP1910. I think that if i set admin state from ip interface to down the L3 features will be disabled, but i´ll need to acess the switch few times, so the switch will still be reacheab...

Firmware update in irf stack

Sandeepani

6 hours ago

Posted to:

Web and Unmanaged

Original author:

Sandeepani

HI I have an issue with updating firmware of the irf stack. I wanted to know how to updatee the firmware of the stack with out getting whole stack down. When configuring the stack we doesent config one by one as that have there any method to upgrade...

HP Procurve MSM 410 AP keeps beeping

Ahzrahn

yesterday

Posted to:

ProCurve / ProVision-Based

Original author:

Ahzrahn

Our Libray has an HP Procurve MSM 410 Wireless Access Point that has been working fine for years. The librarian called me to go onsite stating that the AP was continuously beeping and she had to unplug it and then plug it back in to make it stop. How...

Firmware update in irf stack

Sandeepani

6 hours ago

Posted to:

Web and Unmanaged

Original author:

Sandeepani

Aruba 2930f Switch with multiple VSF domain

JW2018

3 weeks ago

Posted to:

ProCurve / ProVision-Based

Original author:

JW2018

Hi Guys, I need to set up VSF with 9 aruba 2930f switches. I planed to rack 5 aruba 2930f switch on level 1 and 4 aruba 2930f switch on level 2. According to Aruba 2930f manual guide page 742 ' The maximum number of members in a VSF stack is 4 ' So I...

DNS proxy is slow on first request

graphite

Monday

Posted to:

Comware Based

Original author:

graphite

I set up DNS proxy with NAT on MSR3012 router as follows: # nat address-group 1 name PublicIP address <Public IP> <Public IP> # dns proxy enable dns server <ISP DNS1> dns server <ISP DNS2> dns server 8.8.8.8 dns server 8.8.4.4...

Re: Simware HNS 7.1.50 not detecting virtualbox

IanTomkins

Jun 3, 2014

Posted to:

Comware Based

Original author:

drolfe

OK having looked at this further I have found a simple fix for this issue. HNS is expecting an environment variable of VBOX_INSTALL_PATH to be set, it looks like this has changed in the latest version of virtual box to a different name. So to resolve...

Re: HP 1920-8G (JG920A) can't upgrade firmware error "No enough space for uploading the file&qu

Sir Timbit

Jan 15, 2016

Posted to:

Web and Unmanaged

Original author:

Sir Timbit

Found the solution elsewhere...Doing the steps below did the trick.... "I have come across this. The flash cards supplied with HP 1920 switches are pathetically small (32MB in my instance). 1920 firmware is 12MB, and the switch always keeps two...

Re: HP Procurve VLAN Configurations

Vince-Whirlwind

Apr 25, 2017

Posted to:

ProCurve / ProVision-Based

Original author:

LPM89

Just ignore all the stuff about multiple subnets per VLAN. It was the same on Cisco devices - people used to have secondary IP address on their VLAN interface. It is very rare that you would ever have to do this. Your network design should have - - A...

Legend
New Messages
No New Messages
Hot Topic
Replied-to Topic
Read-Only Topic

Events

HPE at 2018 Technology Events

See posts for

dates/locations

Learn about the technology events where Hewlett Packard Enterprise will have a presence in 2018.

Reimagine 2018

See posts for dates/locations

Join us at one of the Reimagine 2018 stops and see how we Simplify Hybrid IT, innovate at the Intelligent Edge and bring it all together with HPE Poin...