- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- ILO problem
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-27-2007 10:14 PM
03-27-2007 10:14 PM
I have configured ILO (IP Address, Subnet mask, GW and username & password).
I cannot access to ILO management via web browser.
I have tried to ping ILO address, OK – I got respond.
I have tried:
- telnet ip_address 80 – port is open
- telnet ip_address 443 –port is open
Thx
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-28-2007 03:20 AM
03-28-2007 03:20 AM
Re: ILO problem
What happens when you try to connect with the browser?
Does it immediately display an error message, or does the error message appear only after the connection timeout (maybe even a minute or more)?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-28-2007 05:36 AM
03-28-2007 05:36 AM
Re: ILO problem
When I try to connect with browser - browser waits and waits and waits - with message in status bar "Opening page..."
Thx
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-28-2007 06:31 AM
03-28-2007 06:31 AM
Re: ILO problem
ILO firmware version: 1.84
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-28-2007 09:13 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-28-2007 01:46 PM
03-28-2007 01:46 PM
Re: ILO problem
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-28-2007 06:25 PM
03-28-2007 06:25 PM
Re: ILO problem
Windows XP SP2
Internet Explorer 6
Java version 1.4.1
I have in p-class 2 Blade BL45p servers
1. ILO work on IP x.x.x.195
2. ILO does not work on IP x.x.x.193
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-29-2007 12:40 PM
03-29-2007 12:40 PM
Re: ILO problem
set your laptop x.x.x.190 and connect cable from laptop directly to management module port, before that reseat Management module physically pull it out and set it back. check if you could pull login screen, if 1st Server works fine and second still not swap Network Mezzanine Adapter and test once again. you can try one more time reseat defaults from F8 and set only IP x.x.x.193 and subnet mask 255.255.255.0.
You had not mentioned if it work from front dongle 192.168.1.1 (your laptop 192.168.1.10)
You did rotate server through enclosure?
No Red LED at Management Modules?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-30-2007 12:56 AM
03-30-2007 12:56 AM
Re: ILO problem
I have tried to reset management module - and I can access to 1st server and cannot access to 2nd server :-(
There is no RED LED at Management module.
I have rotate Blade2: Bay (7-8) -> Bay (5-6).
I can access to 1st server and cannot access to 2nd server :-(
I will reset ILO on 2nd server and set IP address. (I have tried this solution)
I did not understand this operation...
"You had not mentioned if it work from front dongle 192.168.1.1 (your laptop 192.168.1.10)
You did rotate server through enclosure?"
Thank you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-31-2007 04:18 PM
03-31-2007 04:18 PM
Re: ILO problem
...
once you moved server... problem still stay with server ?
test front ILO IP if it works from dongle swap NIC adapter, if no go call HP for system board
user guide for ilo
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00257375/c00257375.pdf
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00212796/c00212796.pdf
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-01-2007 07:17 PM
04-01-2007 07:17 PM
Re: ILO problem
Problem still stay when I move server... :-(
But ILO works from front dongle :-)
IP 192.168.1.1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-02-2007 10:10 AM
04-02-2007 10:10 AM
Re: ILO problem
you have another management module to swap from second enclosure ?
Dejanâ ¦ just update with status, points are not necessary
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-03-2007 01:29 AM
04-03-2007 01:29 AM
Re: ILO problem
I don't have another management module, I have only one Blade p-class enclosure.
Thank you
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-15-2007 06:32 AM
05-15-2007 06:32 AM
Re: ILO problem
anyone ? any idea ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-18-2007 12:16 PM
05-18-2007 12:16 PM
Re: ILO problem
If i unplug the OA eth cable and then plug it back in, i can ping some of the ILOs but not others. Usually 4 or 5 at a time, some of the same ones as before, some new ones and some ones that did work, no longer work. I can never actually ping all 8.
OA nic is connected to datacenter switch. It exibhits same behavior when connected to ethernet switch in the enclosure. Happens when using OA1 or OA2 (OA2 cabled to eth switch 2 or datacenter switch)