- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Controller in a no compaq
Disk Enclosures
1754419
Members
2688
Online
108813
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2001 04:00 PM
тАО02-23-2001 04:00 PM
Controller in a no compaq
I have a smart array 3200 controller with a compaq 10rpm ultra wide
scsi 3 hard disk. I would like to connect them in a clone pc, is it
possible?
I have just tried but unsucessfully. I have bought an SCA 80 to SCSI
68 pin connector and i connect the SA-3200 with the hard disk. At boot
i see the controller testing and then it give me the message no
"logical disk detected".
Post error message 1785.
If i run the array compaq utility i receive
the message no controller present.
Can someone help me?
Thank you in advance
Regards
Gianpaolo
scsi 3 hard disk. I would like to connect them in a clone pc, is it
possible?
I have just tried but unsucessfully. I have bought an SCA 80 to SCSI
68 pin connector and i connect the SA-3200 with the hard disk. At boot
i see the controller testing and then it give me the message no
"logical disk detected".
Post error message 1785.
If i run the array compaq utility i receive
the message no controller present.
Can someone help me?
Thank you in advance
Regards
Gianpaolo
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-03-2001 04:00 PM
тАО04-03-2001 04:00 PM
Re: Controller in a no compaq
The Array Controller is not supported in the PC ....
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-04-2001 04:00 PM
тАО04-04-2001 04:00 PM
Re: Controller in a no compaq
Don't know about the 3200... I have put a Smart 2/P - Smart 2/D in a 'clone' PC and had it work fine. But the 3200 is probably 64 bit PCI (maybe only 33MHz though), so probably wouldn't do much in a "normal" system.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP