- Community Home
- >
- Storage
- >
- Midrange and Enterprise Storage
- >
- HPE EVA Storage
- >
- Secure Path Management CLI
HPE EVA Storage
1753484
Members
4514
Online
108794
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-03-2007 07:46 AM
тАО07-03-2007 07:46 AM
Secure Path Management CLI
What are the command autopath set -t use for?
-t is for timeout. What is LUN timeout value?
-t is for timeout. What is LUN timeout value?
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-03-2007 08:40 PM
тАО07-03-2007 08:40 PM
Re: Secure Path Management CLI
Hi this is what I found from Secure path Manual not sure if u are referring to the same command.
You can also run autopath help
autopath set device
This command sets the Load Balancing policy for the device specified by the
device number.
If no Load Balancing is set for a device, the autopath set device
command sets the Preferred path to the device.
Syntax:
autopath set device=device_number {policy=policy_name |
path=path_number}
device_number is the Auto Path index number shown in the autopath devices
command line display.
policy_name is the Load Balancing policy name.
path_number is the Preferred path number.
Andy
You can also run autopath help
autopath set device
This command sets the Load Balancing policy for the device specified by the
device number.
If no Load Balancing is set for a device, the autopath set device
command sets the Preferred path to the device.
Syntax:
autopath set device=device_number {policy=policy_name |
path=path_number}
device_number is the Auto Path index number shown in the autopath devices
command line display.
policy_name is the Load Balancing policy name.
path_number is the Preferred path number.
Andy
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-03-2007 09:45 PM
тАО07-03-2007 09:45 PM
Re: Secure Path Management CLI
the LUN timeout value is the amount of seconds securepath waits before it markes a path as dead.
A recommended value is 60 seconds if I remember correctly.
A recommended value is 60 seconds if I remember correctly.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP