ftpd and telnetd error

[Gatoux]

my machine are HP 9000/800/L1000-36
the problem :
because of a network's switch update we have changed networks cards to 100FD instead of auto negociate so after the reboot, I have checked everything seemed good, users could connected, loaded application an so on.
but when i had a look on syslog, this message below appeared no longer:

Jan 17 13:39:38 devsigma telnetd[27380]: getpid: peer died: Error 0
Jan 17 13:45:20 devsigma ftpd[27450]: FTP session closed
Jan 17 13:45:26 devsigma telnetd[27452]: getpid: peer died: Error 0
Jan 17 13:50:52 devsigma ftpd[27522]: FTP session closed
Jan 17 13:50:58 devsigma telnetd[27524]: getpid: peer died: Error 0
Jan 17 13:51:45 devsigma ftpd[27609]: FTP session closed
Jan 17 13:51:51 devsigma telnetd[27613]: getpid: peer died: Error 0
Jan 17 13:52:07 devsigma ftpd[27615]: FTP session closed
Jan 17 13:52:13 devsigma telnetd[27617]: getpid: peer died: Error 0
Jan 17 14:43:17 devsigma ftpd[28274]: FTP session closed
Jan 17 14:43:23 devsigma telnetd[28276]: getpid: peer died: Error 0
Jan 17 14:45:36 devsigma ftpd[28279]: FTP session closed
Jan 17 14:45:42 devsigma telnetd[28281]: getpid: peer died: Error 0
Jan 17 14:47:36 devsigma ftpd[28323]: FTP session closed
Jan 17 14:47:42 devsigma telnetd[28325]: getpid: peer died: Error 0
Jan 17 14:49:36 devsigma ftpd[28329]: FTP session closed
Jan 17 14:49:42 devsigma telnetd[28331]: getpid: peer died: Error 0
Jan 17 14:51:36 devsigma ftpd[28356]: FTP session closed
Jan 17 14:51:42 devsigma telnetd[28358]: getpid: peer died: Error 0
Jan 17 14:53:36 devsigma ftpd[28403]: FTP session closed
Jan 17 14:53:42 devsigma telnetd[28405]: getpid: peer died: Error 0
Jan 17 14:55:36 devsigma ftpd[28410]: FTP session closed
Jan 17 14:55:42 devsigma telnetd[28412]: getpid: peer died: Error 0
Jan 17 14:57:36 devsigma ftpd[28477]: FTP session closed
Jan 17 14:57:42 devsigma telnetd[28479]: getpid: peer died: Error 0

Someone can help me please about this ?

tks

[Sanjay_6]

Hi,

Make sure the port on the switch is also set to 100Full Duplex / Fixed / no autoneg

You should have this setting on both the server as well as the switch.

If you change the setting on one but not on the other, you may have this problem.

Hope this helps.

Regds

[Peter Godron]

Hi,
have a look at :
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=501458
Telnet connections are beeing terminated, either by users without logging off, or by processes.
Regards

[Gatoux]

Hi Sanjay,

I have already checked it, the switch's port set in 100FD.

[Gatoux]

thanks Peter i will have look on the link