install

[Edward Shabotinsky]

When running install from scratch for 10.20 or 11.0, having error massage WARN80F5 and also STATUS= -7.
Any boddy could help me with this
I have two CD-ROM's for 10.20 and 11.0
#model 9000/821/D350
Thanks

[Stefan Farrelly]

- Its a bad SCSI termination, or a bad CD-device.
- URL with the possible solution:

http://us-support2.external.hp.com/cki/bin/doc.pl/sid=3D08a68c551a1d98cd9=
8/screen=3DckiDisplayDocument?Id=3D200000050964288

[Stefan Farrelly]

oops, that link didnt come out too good, heres a better one;

http://europe-support2.external.hp.com/cki/bin/doc.pl/sid=0594cf451c992b5373/screen=ckiDisplayDocument?docId=200000050964288

[Tom Wittenberg_1]

The error you are getting is that it is having trouble getting to the path for the CD-Rom drive the default path on a D350 is usually 8/16/5.2 if you have 2 drives your second you might be 8/16/5.1. You can boot up to the prompt(main menu) and type ?search ipl? and if the cdrom disk is in the drive and it is bootable it should come back with a path. At that point you should be able to boot from it w/ bo ?PATH ID? describe with the ?search ipl? command. If the drive is installed and the cdrom doesn?t blink like it is being search you my have a bad interface card.

Problems Using the CD-ROM Drive
After the self-test, the status LED stays ON when one of the following conditions
exist:
? A defective disk
? A disk insertion error (for example, an upside-down disk)
After the self-test, the status LED goes OFF when one of the following conditions
exist:
? A drive power failure exists.
? The drive is idle on the SCSI bus.
? The drive is ready with the disk installed.
Problem Solution
The CD-ROM drive does
not respond when a disk is
loaded or the status LED
stays on.
Re-load the disk. Check the status of the status LED.
See Below:


Using Your CD-ROM Drive
HP A3416A and A3715A CD-ROM Drives
Table 3-6 CD Unloading in the Vertical Mount Position
Reading the Drive Status LED
1. After Drawer is closed:
a. LED OFF after short blinking sequence = Drive Ready or Stand-by.
b. LED ON = No disk present.
c. LED Blinking at 3.2 second interval = Cleaning of disk or optics required.
2. While Playing an Audio Track:
a. LED Blinking at 1.6 second interval.
3. When Accessing Data:
a. LED Steady.
Vertictal Mount Unloading
1. Wait for the CD-ROM drive activity to
stop.
2. Press the Eject Button.
3. Snap the top retaining tabs (A, B) away
from the CD and remove the CD from its
tray.

Using Your CD-ROM Drive
Operating the HP A3184A CD-ROM Drive
? You turn on the computer with a disk already loaded in the CD-ROM drive.
During the self-test, the status LED operates in the following sequence:
1. LED On - The status LED goes on when the disk loads into the drive.
2. LED Flashing - The LED flashes while a read test is performed on the disk.
3. LED Off - The LED goes off when the self-test is complete.
After the self-test, the LED flashes when there is disk activity.

[Tom Wittenberg_1]

Seem's to have formatting problems in ITRC


The error you are getting is that it is having trouble getting to the path for the CD-Rom drive the default path on a D350 is usually 8/16/5.2 if you have 2 drives your second you might be 8/16/5.1. You can boot up to the prompt(main menu) and type ?search ipl? and if the cdrom disk is in the drive and it is bootable it should come back with a path. At that point you should be able to boot from it w/ bo ?PATH ID? describe with the ?search ipl? command. If the drive is installed and the cdrom doesn?t blink like it is being search you my have a bad interface card.

Problems Using the CD-ROM Drive
After the self-test, the status LED stays ON when one of the following conditions
exist:
? A defective disk
? A disk insertion error (for example, an upside-down disk)
After the self-test, the status LED goes OFF when one of the following conditions
exist:
? A drive power failure exists.
? The drive is idle on the SCSI bus.
? The drive is ready with the disk installed.
Problem Solution
The CD-ROM drive does
not respond when a disk is
loaded or the status LED
stays on.
Re-load the disk. Check the status of the status LED.
See Chapter 3, ?Reading the Drive Status Light.? If
an error condition occurs, contact your System
Administrator.

Using Your CD-ROM Drive
HP A3416A and A3715A CD-ROM Drives
Table 3-6 CD Unloading in the Vertical Mount Position
Reading the Drive Status LED
1. After Drawer is closed:
a. LED OFF after short blinking sequence = Drive Ready or Stand-by.
b. LED ON = No disk present.
c. LED Blinking at 3.2 second interval = Cleaning of disk or optics required.
2. While Playing an Audio Track:
a. LED Blinking at 1.6 second interval.
3. When Accessing Data:
a. LED Steady.
Vertictal Mount Unloading
1. Wait for the CD-ROM drive activity to
stop.
2. Press the Eject Button.
3. Snap the top retaining tabs (A, B) away
from the CD and remove the CD from its
tray.

Using Your CD-ROM Drive
Operating the HP A3184A CD-ROM Drive
? You turn on the computer with a disk already loaded in the CD-ROM drive.
During the self-test, the status LED operates in the following sequence:
1. LED On - The status LED goes on when the disk loads into the drive.
2. LED Flashing - The LED flashes while a read test is performed on the disk.
3. LED Off - The LED goes off when the self-test is complete.
After the self-test, the LED flashes when there is disk activity.

[Tom Wittenberg_1]

Here is a word ducument that might be easier to read!