Installaton Problem Urgent

[sanalp]

While installing hp unix 11.11 i am getting an error after all the file system selection when i select the GO tab installation is starting but its giving error .its customized os.
during installation i select install hp ux>media install>advance installation....

i am not installing through ignite server...

error is

* Running command: "/usr/sbin/swinstall -s/tmp/ign_configure/SD_CDROM
-f/tmp/ign_configure/software_file -x os_release=B.11.11 -x
os_name=HP-UX:64 -xpatch_filter=*.* -xpatch_save_files=true "
WARNING: The software specified contains a fileset that changes the
kernel. Either the attribute dynamic_module, used for dynamic
changes, is specified, or the is_kernel attribute, used for
static changes, is set to true.

* Beginning Analysis Phase.
* Source: localhost:/tmp/ign_configure/SD_CDROM
* Target: loopback:/
* Target logfile: loopback:/var/adm/sw/swagent.log
* Reading source for product information.
NOTE: The filesystems in the filesystem table will not be checked
against those currently mounted because the
"mount_all_filesystems" option is set to "false".
* Reading source for file information.
ERROR: File
"/tmp/ign_configure/SD_CDROM/catalog/SW-DIST/pfiles/INDEX":
I/O error (5). Cannot copy it to file
"/var/tmp/BAAa00139/catalog/SW-DIST/pfiles/INDEX".
ERROR: File
"/tmp/ign_configure/SD_CDROM/catalog/SW-DIST/pfiles/install-sd":
I/O error (5). Cannot copy it to file
"/var/tmp/BAAa00139/catalog/SW-DIST/pfiles/install-sd".
ERROR: File
"/tmp/ign_configure/SD_CDROM/catalog/SW-DIST/pfiles/swagent.Z":
I/O error (5). Cannot copy it to file
"/var/tmp/BAAa00139/catalog/SW-DIST/pfiles/swagent.Z".
ERROR: The catalog files for product "SW-DIST,r=B.11.11.0406" failed
to load. Check the above output for details.
ERROR: File
"/tmp/ign_configure/SD_CDROM/catalog/ProgSupport/pfiles/INFO":
I/O error (5). Cannot copy it to file
"/var/tmp/BAAa00139/catalog/ProgSupport/pfiles/INFO".
ERROR: The catalog files for product "ProgSupport,r=B.11.11" failed
to load. Check the above output for details.
ERROR: Cannot continue the Analysis Phase until the previous errors
are corrected.
ERROR: RPC exception: "Communications failure (dce / rpc)" 05/14/08
12:37:28 EDT
ERROR: Could not perform the requested operation for "loopback:/",
possibly due to a network communications failure or the agent
timing out. Check that the host is still accessible from the
network, and the agent_timeout_minutes option is not set too
low.
NOTE: run_cmd: Process: 138 (/usr/sbin/swinstall): killed by signal: 11
(core dumped).
ERROR: Software load had one or more errors.

======= 05/14/08 12:37:29 EDT The operating system software has not been
successfully loaded. The swinstall(1M) application was not completed
or failed to load some key files. (exit status was = -1).

1: Change the swinstall server and/or depot information.
2: Retry software load process (non-interactive mode).
3: Retry software load process (interactive mode).
4: Run a shell.
Choose a recovery action from above:


* Running command: "/usr/sbin/swinstall -s/tmp/ign_configure/SD_CDROM
-f/tmp/ign_configure/software_file -x os_release=B.11.11 -x
os_name=HP-UX:64 -xpatch_filter=*.* -xpatch_save_files=true "
WARNING: The software specified contains a fileset that changes the
kernel. Either the attribute dynamic_module, used for dynamic
changes, is specified, or the is_kernel attribute, used for
static changes, is set to true.

* Beginning Analysis Phase.
* Source: localhost:/tmp/ign_configure/SD_CDROM
* Target: loopback:/
* Target logfile: loopback:/var/adm/sw/swagent.log
* Reading source for product information.
NOTE: The filesystems in the filesystem table will not be checked
against those currently mounted because the
"mount_all_filesystems" option is set to "false".
* Reading source for file information.
ERROR: File
"/tmp/ign_configure/SD_CDROM/catalog/SW-DIST/pfiles/INDEX":
I/O error (5). Cannot copy it to file
"/var/tmp/BAAa00139/catalog/SW-DIST/pfiles/INDEX".
ERROR: File
"/tmp/ign_configure/SD_CDROM/catalog/SW-DIST/pfiles/install-sd":
I/O error (5). Cannot copy it to file
"/var/tmp/BAAa00139/catalog/SW-DIST/pfiles/install-sd".
ERROR: File
"/tmp/ign_configure/SD_CDROM/catalog/SW-DIST/pfiles/swagent.Z":
I/O error (5). Cannot copy it to file
"/var/tmp/BAAa00139/catalog/SW-DIST/pfiles/swagent.Z".
ERROR: The catalog files for product "SW-DIST,r=B.11.11.0406" failed
to load. Check the above output for details.
ERROR: File
"/tmp/ign_configure/SD_CDROM/catalog/ProgSupport/pfiles/INFO":
I/O error (5). Cannot copy it to file
"/var/tmp/BAAa00139/catalog/ProgSupport/pfiles/INFO".
ERROR: The catalog files for product "ProgSupport,r=B.11.11" failed
to load. Check the above output for details.
ERROR: Cannot continue the Analysis Phase until the previous errors
are corrected.
ERROR: RPC exception: "Communications failure (dce / rpc)" 05/14/08
12:37:28 EDT
ERROR: Could not perform the requested operation for "loopback:/",
possibly due to a network communications failure or the agent
timing out. Check that the host is still accessible from the
network, and the agent_timeout_minutes option is not set too
low.
NOTE: run_cmd: Process: 138 (/usr/sbin/swinstall): killed by signal: 11
(core dumped).
ERROR: Software load had one or more errors.

======= 05/14/08 12:37:29 EDT The operating system software has not been
successfully loaded. The swinstall(1M) application was not completed
or failed to load some key files. (exit status was = -1).

1: Change the swinstall server and/or depot information.
2: Retry software load process (non-interactive mode).
3: Retry software load process (interactive mode).
4: Run a shell.
Choose a recovery action from above:



following is the boot procedure i followed..


IODC
Path# Device Path (dec) Device Path (mnem) Device Type Rev
----- ----------------- ------------------ ----------- ----
P0 0/0/2/0.0 ide.0 Random access media 1

P1 0/1/1/0.0 intscsia.0 Random access media 1

P2 0/1/1/1.3 intscsib.3 Sequential access media 1



Main Menu: Enter command or menu > BO P0
Interact with IPL (Y, N, or Cancel)?> N

Booting...
Boot IO Dependent Code (IODC) revision 1


HARD Booted.

ISL Revision A.00.43 Apr 12, 2000

ISL booting hpux (;0):INSTALL

Boot
: disk(0/0/2/0.0.0.0.0.0.0;0):WINSTALL
11763712 + 1970264 + 2628048 start 0x200ae8




alloc_pdc_pages: Relocating PDC from 0xfffffff0f0c00000 to 0x3f700000.
gate64: sysvec_vaddr = 0xc0002000 for 2 pages
NOTICE: nfs3_link(): File system was registered at index 4.
NOTICE: autofs_link(): File system was registered at index 6.
NOTICE: cachefs_link(): File system was registered at index 7.
igelan0: INITIALIZING HP PCI 1000Base-T Core at hardware path 0/1/2/0
igelan1: INITIALIZING HP A6825-60101 PCI 1000Base-T Adapter at hardware path 0/4
/1/0

System Console is on the Built-In Serial Interface
Swap device table: (start & size given in 512-byte blocks)
entry 0 - auto-configured on root device; ignored - no room
WARNING: no swap device configured, so dump cannot be defaulted to primary swap.
WARNING: No dump devices are configured. Dump is disabled.
Starting the STREAMS daemons-phase 1
Create STCP device files
$Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'V
w for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed
Nov 8 19:24:56 PST 2000 $
Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 1046528 Kbytes, lockable: 719572 Kbytes, available: 844308 Kbytes

======= 05/14/08 13:25:20 EDT HP-UX Installation Initialization. (Wed May 14
13:25:20 EDT 2008)
@(#) Ignite-UX Revision B.5.4.38
@(#) install/init (opt) $Revision: 10.285 $
* Scanning system for IO devices...
* Querying disk device: 0/1/1/0.0.0 ...
* Querying graphics device: 0/3/1/0 ...WARNING: Cannot open (/dev/crt0):
No such file or directory (errno = 2)
* Setting keyboard language.

A USB interface has been detected on this system.
In order to use a keyboard on this interface, you must specify
a language mapping which will be used by X windows and
the Internal Terminal Emulator (ITE).
The characters "1234567890" will appear as "!@#$^&*()"
on keyboards that use the shift key to type a number.
Your choice will be stored in the file /etc/kbdlang


1) USB_PS2_DIN_Belgian 2) USB_PS2_DIN_Belgian_Euro
3) USB_PS2_DIN_Danish 4) USB_PS2_DIN_Danish_Euro
5) USB_PS2_DIN_Euro_Spanish 6) USB_PS2_DIN_Euro_Spanish_Euro
7) USB_PS2_DIN_French 8) USB_PS2_DIN_French_Euro
9) USB_PS2_DIN_German 10) USB_PS2_DIN_German_Euro
11) USB_PS2_DIN_Italian 12) USB_PS2_DIN_Italian_Euro
13) USB_PS2_DIN_JIS_109 14) USB_PS2_DIN_Korean
15) USB_PS2_DIN_Norwegian 16) USB_PS2_DIN_Norwegian_Euro
17) USB_PS2_DIN_S_Chinese 18) USB_PS2_DIN_Swedish
19) USB_PS2_DIN_Swedish_Euro 20) USB_PS2_DIN_Swiss_French2_Euro
21) USB_PS2_DIN_Swiss_German2 22) USB_PS2_DIN_Swiss_German2_Euro
23) USB_PS2_DIN_T_Chinese 24) USB_PS2_DIN_UK_English
25) USB_PS2_DIN_UK_English_Euro 26) USB_PS2_DIN_US_English
27) USB_PS2_DIN_US_English_Euro

Enter the number of the language you want

[Torsten.]

What server model do you have and what OS version do you install (release date)?

All the I/O errors point IMHO to bad hardware (CD media, CD drive, HDD ...).

[sanalp]

Server model is rp3410.i am going to inall hp unix 11.11 and i got the CD fromhe customer is hp unix 11i operating enviornment june 2004 version.its an customized os.i am also suspecting the media (cd) only.but i dont know why its showing some ignite unix related things like the source /tmp/ign_configure/sd_cdrom..
and during boot from cd its showing

05/14/08 13:25:20 EDT HP-UX Installation Initialization. (Wed May 14
13:25:20 EDT 2008)
@(#) Ignite-UX Revision B.5.4.38
@(#) install/init (opt) $Revision: 10.285 $
* Scanning system for IO devices...
* Querying disk device: 0/1/1/0.0.0 ...
* Querying graphics device: 0/3/1/0 ...WARNING: Cannot open (/dev/crt0):
No such file or directory (errno = 2)
* Setting keyboard language.



thanks....

[Torsten.]

Don't worry about the graphics device. It is installed, but not supported. This piece of hardware is the same as in another server (rx2600), but only supported there.


IMHO I would use another __newer__ install media. June 2004 is a bit old.

Try to verify the CD in another system if it is readable and consider to use a newer media.