- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: assign UIC on group, member
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-13-2010 05:26 PM
тАО07-13-2010 05:26 PM
grant/iden menue ABC
%UAF-E-GRANTUSR, user identifier ABC does not exist; MENUE could not be granted
Checked the UIC, it shows:
UIC: [200,1757] ([200,1757])
How can we change to [group, member] instead of the numbering behind. this ([200,1757])
is suppose to be shown as [COMETS, ABC]
Thanks in advance!
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-13-2010 05:42 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-13-2010 05:48 PM
тАО07-13-2010 05:48 PM
Re: assign UIC on group, member
Your user "ABC" doesn't have an associated identifier. The easiest way to make one is:
UAF> ADD/IDENT/USER=ABC
You should also review your procedures to try to work out why the identifier wasn't created when the user was created. It should happen by default. Check to see what other users are missing identifiers:
$ pipe mcr authorize show * | search sys$pipe "UIC:"
Look for other users with a numeric UIC in parentheses.
you can create then with
UAF> ADD/IDENT/USER=*
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-13-2010 06:05 PM
тАО07-13-2010 06:05 PM
Re: assign UIC on group, member
For a start, please do an AUTHORIZE SHOW ABC/FULL.
Also, verify that AUTHORIZE is either:
- being run following a SET DEFAULT SYS$SYSTEM; or
- that logical names are properly assigned for SYSUAF and RIGHTSLIST
- Bob Gezelter, http://www.rlgsc.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-13-2010 07:15 PM
тАО07-13-2010 07:15 PM
Re: assign UIC on group, member
Similar topic was discussed in the below threads.
http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1151194
http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1237997
May be helpful.
Regards,
Ketan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-14-2010 07:24 PM
тАО07-14-2010 07:24 PM
Re: assign UIC on group, member
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-15-2010 03:03 AM
тАО07-15-2010 03:03 AM
Re: assign UIC on group, member
As mentioned above, your problem is that the user ABC was not added to the Rightslist when he/she/it was created.
If you create users using the "ADD" command, then Identifiers are automatically added to the rightslist, however if you create a user by copying an existing user, I think you have to add the identifier manually. I am just including this because you didn't mention how the UAF record was created.
If you DID use the "ADD" command, and the Identifier was not automatically added, then I would follow Bob's suggestion and check that the RIGHTSLIST is accessable, either by being defined logically, or it is in your current default directory.
A common cause for identifiers not being added it when the UIC is already being used by another user, although this will generate a different error message. Just as a check however, I would try
UAF> show [200,1745] /brief
HTH
Dave.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-15-2010 01:01 PM
тАО07-15-2010 01:01 PM
Re: assign UIC on group, member
Where there are multiple uncoordinated rightslist files and where the identifiers within the cluster are, well, skewed.
That would be bad.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-15-2010 01:24 PM
тАО07-15-2010 01:24 PM
Re: assign UIC on group, member
I suspect that you are correct. That is why I asked for the SHOW output earlier in this thread.
- Bob Gezelter, http://www.rlgsc.com