HPE GreenLake Administration
- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Pathworks Remote Boot problem...
Operating System - OpenVMS
1828355
Members
3273
Online
109976
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-12-2007 03:55 AM
03-12-2007 03:55 AM
Pathworks Remote Boot problem...
I have a PC that remote boots using a DE203 NIC to a Pathworks 4 server. The NIC went faulty and was replaced. I have used ezworks.exe to tell the card that remote boot is enabled. On the Pathworks 4 server I have in NCP set and def the node char to have the replacement NIC hardware address. A repl/enable sees the pc being loaded, but on the PC the following message appears.
EWRK3 Remote Boot TSK Image Version V2.00.000
Copyright © 1993 by Digital Equipment Corporation
Fatal Error: TSR failed, can not continue ….
Anyone with any ideas what could be wrong?
Thanks Nigel.
EWRK3 Remote Boot TSK Image Version V2.00.000
Copyright © 1993 by Digital Equipment Corporation
Fatal Error: TSR failed, can not continue ….
Anyone with any ideas what could be wrong?
Thanks Nigel.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-13-2007 07:07 AM
03-13-2007 07:07 AM
Re: Pathworks Remote Boot problem...
Wow, that's going back to WFWG & PW for DOS days! The EWRK3.DOS image (DEC EtherWORKS 3 driver) is trying to load (TSR) and doesn't find the right configuration. There are files on the PC and also on the server (the network key disk) that hold config data, so you need to go through the PC's PW setup again; NETSETUP at least. Then, your old software and new NIC may or may not get along. The old stuff was pretty picky about the NIC. AFA any tricks to try, that was too long ago for me to remember.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
Company
Support
Events and news
Customer resources
© Copyright 2025 Hewlett Packard Enterprise Development LP