- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- Re: firmware upgrade gone bad
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-09-2005 10:46 AM
тАО08-09-2005 10:46 AM
firmware upgrade gone bad
During the process of upgrading an iLO firmware to 1.75, the transfer was interrupted.
I attempted again (successfully it seemed), but now, the only service running on the host is ftp.
% ftp lom
Connected to lom.
220 FTP flash recovery server ready.
530 access denied.
530 access denied.
KERBEROS_V4 rejected as an authentication type
Name (lom.jersey.hcmny.com:root): ftp
530 access denied.
Login failed.
ftp>
not good news it seems.
Is there anything that I can do with that ftp server to get the device again to a usable state (preferrably without physical access to the machine)?
thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-09-2005 09:43 PM
тАО08-09-2005 09:43 PM
Re: firmware upgrade gone bad
ftp iloIP
Use the following username and password
User: flash
Password: recovery
then, mput ilo175.bin (in binary mode)
The iLO should upgrade the firmware
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-19-2009 04:07 AM
тАО02-19-2009 04:07 AM
Re: firmware upgrade gone bad
I have the same problem: the only service running on the host is ftp.
I've successfully flushed iLO as [pratap m keshava] said before with ilo193.bin but there is still no response from webserver on iLO.
Is power off/on needed after flushing?
It hasn't been done yet because it's Domain Controller...
Thanks in advance,
WBR, Andrew.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-19-2009 07:03 PM
тАО02-19-2009 07:03 PM
Re: firmware upgrade gone bad
If SSH/Telnet is open, then login to iLO by providing the iLO username/password.
Then type in the command prompt.
"cd map1". This will change to iLO directory.
then type "reset". This will reset the firmware. All open sessions will be terminated. You should be able to login after approx 1 minute.
Otherwise you may need to physically remove the power to the server and after a gap of about 30 seconds insert power cable back. Just restarting of server won't help.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-19-2009 11:50 PM
тАО02-19-2009 11:50 PM
Re: firmware upgrade gone bad
there is no ssh/telnet response.
after power off (with removing cables) there is no ftp response, even no iLO prompt via POST process any more:(
can I try something else or it's a HW problem?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-20-2009 04:25 AM
тАО02-20-2009 04:25 AM