- Community Home
- >
- Networking
- >
- Software Defined Networking
- >
- 2920 no clients recognized
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-20-2014 08:56 AM
08-20-2014 08:56 AM
2920 no clients recognized
I have installed controller 2.3.6 and optimizer 1.2
I have successful connection to lync and can see lync sessions on controller.
i have also enabled netflow on controller v 1.3 and passive mode.
But i cannot see clients on topology map.
switch is shown correctly.
when i check from switch it also shows connection to controller.
because of this problem i can not assign dscp values to clients.
also clients were working very slow until we increased hardware limit which was 0 by default.
is there anything that needs to be done to recognize clients?
Regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-09-2014 11:30 AM
09-09-2014 11:30 AM
Re: 2920 no clients recognized
Hello mertdemi,
Apologies for the delay.
We are looking in to your query will get back to you soon.
However could you please comment on the below details-
1.Controller version used is 2.3.5 ?
2.Network Optimizer 1.1.5 ?
3. Switch config/firmware version/details
4.Open Flow version enabled?
We hope you have followed the steps mentioned in HP Network Optimizer SDN Application-Microsoft Lync 1.1 installation guide.
Thanks,
HP SDN Team
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-10-2014 01:20 AM
09-10-2014 01:20 AM
Re: 2920 no clients recognized
with 2.2.5 i dont have performance problem but i can not see clients still on topology viewer
i have changed arp timeout to 20 minutes but no change.
switch is 2920
Passive mode firmware version wb.15.14.0007
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-26-2014 01:11 AM
09-26-2014 01:11 AM
Re: 2920 no clients recognized
Hello mertdemi,
Could you please provide answers to the below questions:
- Is the client sending any traffic to the OpenFlow switch? If yes, what traffic ?
- What are the rules programmed in the OpenFlow switch ? Does it have any rules other than the default rules installed by the controller ?
- Does the controller receive the packet_in messages from the switch ?
Thanks,
HP SDN Team