- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: VC flex10g Ethernet uplink faild
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2011 01:44 PM
тАО01-06-2011 01:44 PM
VC flex10g Ethernet uplink faild
I'm installing C7000 with 10 BL460c G6.
I want to configure 4 uplinks from VC flex10g Ethernet to be used in a single network. I have connected (Bay 1 port X1, Bay 1 port X2, Bay 2 port X1, Bay 2 port X2) to my DC switch and when ever I try to run the network set-up wizard it show my connected links are Not linked al though they are connected to my local switch and my local switch is working properly.
please see the attachment and advice
Regards
Adil Elamin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2011 02:00 PM
тАО01-06-2011 02:00 PM
Re: VC flex10g Ethernet uplink faild
Note: on 11-2010 the configuration made by HP (factory integrated)
however after I logged to the VCM the previous setting have been lost
Regards
Adil
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2011 02:30 PM
тАО01-06-2011 02:30 PM
Re: VC flex10g Ethernet uplink faild
I tried to connect one VC physical uplink port directly with my laptop and it come up, but the link never come up when ever I connect it to my DC switch cisco 2950.
Regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2011 08:09 PM
тАО01-06-2011 08:09 PM
Re: VC flex10g Ethernet uplink faild
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-07-2011 01:00 AM
тАО01-07-2011 01:00 AM
Re: VC flex10g Ethernet uplink faild
it show up when ever I connect the physical link to another device, but it show down whenever I connect it to my DC switch.
I think VC will operate only with 100MB/S switched network and higher only.
Regards
Adil
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-07-2011 01:10 AM
тАО01-07-2011 01:10 AM
Re: VC flex10g Ethernet uplink faild
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-07-2011 06:01 AM
тАО01-07-2011 06:01 AM
Re: VC flex10g Ethernet uplink faild
It is supported on the older 1/10g VC modules.
Dave.