- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: Why I cannot make lan0 lan card up?
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-12-2000 07:37 AM
тАО05-12-2000 07:37 AM
Why I cannot make lan0 lan card up?
HI,
I am trying to let my HP 9000/300 system go through the internet.(it worke one or two years ago,for this time I use another static IP address because we moved the system )
But I even cann't ping myself IP address now.
(I used ifconfig to set IP,netmask...I checked /etc/hosts,netstat -rn...)
I use lanscan to find the information below:
21 0x080009352A952 0 DOWN lan0 DOWN 3 ETHER IEEE8023
So this means lan0 is down.
I use ifconfig lan0 up,but it didn't work.It showed up no such interface.But I can use ifconfig lo0 up or down.
So what is the problem?Maybe the lan0 card is bad or I haven't set something right?
BTW,my HP UNIX OP systen is very old(maybe 10 years),I think it is version 0.0,But I think the ifconfig command should be the same.
I need helps!
Thank you very much.
Billy Kidd
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-12-2000 07:45 AM
тАО05-12-2000 07:45 AM
Re: Why I cannot make lan0 lan card up?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-12-2000 07:50 AM
тАО05-12-2000 07:50 AM
Re: Why I cannot make lan0 lan card up?
Is the cable properly connected to the hub or switch. Maybe changing the port on the hub and/or rebooting the server will help.
Until the lancard is in the "hardware" up state, you will not be able to configure the lancard.
After you get the lancard functional, you will need to set a gateway that will allow you to get to the Internet. The gateway must be on the same subnet as the server; and it must be accessible by the server.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-12-2000 02:34 PM
тАО05-12-2000 02:34 PM
Re: Why I cannot make lan0 lan card up?
I am very glad to get helps!
when I use command ifconfig lan0 it comes out:
lan0: flags=62
inet IP netmask ffffff00 broadcast ...
(But each time I reboot the system I need to reconfig the lan0,the system cann't AUTO config when it was booting,something showed that sytem tryed to config but just can not find such interface,when I run ifconfig lan0 up it also showed ifconfig : no such interface)
And I am sure that the port that HP server plug in is good because my WIN98 PC can access the INTERNET through this port.
BTW,there is a transciever between the lan card and the port(I use the lan BNC port),and the lighters on it seem ok.
So,what can I do now?Why the lan0 lan card can not be active?And each time I try to ping myself static IP address it shows: no route to host.
I do need more helps!
Thanks a lot!
billy Kidd
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-20-2000 05:20 AM
тАО05-20-2000 05:20 AM
Re: Why I cannot make lan0 lan card up?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-20-2000 07:39 AM
тАО05-20-2000 07:39 AM
Re: Why I cannot make lan0 lan card up?
it is probably at 8.x or 9.x
Do uname -a to get OS revision.
Network info is kept in a file called /etc/netlinkrc at these older revs.
I also think that from your explanatiion, you have plugged in the BNC connetcor, but there is also a transceiver?
these do not auto select, you would need to remove the card on which the lan port is, and verify whether there is a slector bank to elect AUI or internal transceiver to allow you to use the BNC.
HTH
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-08-2000 04:13 PM
тАО06-08-2000 04:13 PM
Re: Why I cannot make lan0 lan card up?
can you go to sam, network, network interfaces?
This should allow you to configure via menus.