- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: superdome replacement user guide
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-05-2006 11:13 PM
тАО09-05-2006 11:13 PM
superdome replacement user guide
i need to replace a superdome's backplane power board, but i don't have such experience, can you present me some hints or some guide?
thanks a lot
stephen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-06-2006 04:47 AM
тАО09-06-2006 04:47 AM
Re: superdome replacement user guide
This doc should do it for you:
http://docs.hp.com/en/A5201-96044/index.html
Regards,
Jaime.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-06-2006 03:52 PM
тАО09-06-2006 03:52 PM
Re: superdome replacement user guide
there is no recommandation about replacing HBPB in that document. after all, thank you for your reply.
stephen
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-06-2006 04:22 PM
тАО09-06-2006 04:22 PM
Re: superdome replacement user guide
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-06-2006 06:16 PM
тАО09-06-2006 06:16 PM
Re: superdome replacement user guide
There should be atleast 2 HBPBs installed which works on load-balancing mode. They are hot-swappable.
I have seen the HP CE doing this job.For replacing the HBPB, you need to
1. Open the rear cabinet door and remove the EMI panel.
You would see the HBPBs and you can identify the faulty one with LED indication off
2. Loosen the 2 thumbscrews on the board
3. Grasp the handle of the board and pull it carefully.
4. Replace the board with new one and tighten the screws.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-09-2006 04:24 PM
тАО09-09-2006 04:24 PM
Re: superdome replacement user guide
I would not suggest replacing the Backplane all by yourself. God forbidden something should happen HP would not take any responsibility... Check the replacement procedure for your information..
Shut down the server:
From the Command Menu, enter pe.
Enter the number of the cabinet to power off.
When prompted for the state of the cabinet power, enter off.
Turn off the AC breakers on the PDCA(s) at the back of the each cabinet.
Remove the power plug from the power source.
Put on an electrostatic discharge (ESD) wrist strap to avoid damaging any circuitry.
============================================
A backplane contains a maximum of three Backplane Power Boards (HBPB) that are located on the opposite side from the cell boards.
The HBPB supplies are N+1 (N = 2) redundant for +1.8 VDC power and N+2 (N = 1) redundant for +3.3 VDC power.
Each HBPB contains a DC-to-DC converter for each of these voltages.
These converters support current sharing with the other HBPBs in the system.
The HBPBs are accessible from the rear of the cabinet and are hot swappable.
Backplane power board removal :
--------------------------------
Open the rear cabinet door.
Remove the rear EMI panel.
Locate the backplane power board on the back of the system backplane.
Loosen the two T-20 retaining screws.
Remove the power board by grasping the handle and pulling the power board from the backplane.
Backplane power board replacement:
----------------------------------
Position and install the power board into the back of the system backplane.
Tighten the two T-20 screws.
Replace the rear EMI panel.
Close the rear cabinet door.
Best Regards,
Parshanth