- Community Home
- >
- HPE Community, Korea
- >
- HP-UX
- >
- 싱글 유저 모드 방법
범주
Company
Local Language
포럼
토론 게시판
포럼
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
토론 게시판
토론 게시판
포럼
토론 게시판
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
포럼
블로그
- 신규로 표시
- 북마크
- 구독
- 소거
- RSS 피드 구독
- 강조
- 인쇄
- 부적절한 컨텐트 신고
날짜: 10-25-2005 10:00 PM
날짜: 10-25-2005 10:00 PM
싱글 유저 모드 방법
OS : HP-UX hp-ux B.11.11
싱글 유저로 부팅하기 위해서 아래와 같이 했지만 싱글로 들어가지 않는데 답변 좀 부탁 드리겠습니다.
***** EARLY BOOT VFP : SYSTEM ALERT *****
SYSTEM NAME: HPUX
DATE: 10/25/2005 TIME: 07:42:35
ALERT LEVEL: 6 = Boot possible, pending failure - action required
REASON FOR ALERT
SOURCE: 8 = I/O
SOURCE DETAIL: 9 = serial SOURCE ID: 0
PROBLEM DETAIL: 3 = functional failure
LEDs: RUN ATTENTION FAULT REMOTE POWER
FLASH FLASH OFF ON ON
LED State: Running non-OS code. Non-critical error detected.
Check Chassis and Console Logs for error messages.
0x00000063890014C0 00000000 00000000 - type 0 = Data Field Unused
0x58000863890014C0 00006909 19072A23 - type 11 = Timestamp 10/25/2005 07:42:35
A/a: ack read of this entry - Q/q: quit Virtual Front Panel Display
Anything else redisplay the log entry
-> Choice : a <== a 입력
Main Menu: Enter command or menu > bo
Interact with IPL (Y, N, or Cancel)?> y <== ISL 판넬로 들어감
ISL> autoboot off <== off로 설정
ISL> di <== 확인
Fastsize value is 0000000F
Autoboot is OFF (disabled)
Autosearch is ON (enabled)
Primary boot path is 0/0/2/1.15.0.0.0.0.0
Primary boot path is (hex) 0/0/2/1.F.0.0.0.0.0
Alternate boot path is 0/0/2/0.5.0.0.0.0.0
Alternate boot path is (hex) 0/0/2/0.5.0.0.0.0.0
System console path is 0/0/4/0.643.0.0.0.0.0
System console path is (hex) 0/0/4/0.283.0.0.0.0.0
ISL> hpux -is <== 싱글로 부팅
unknown/]who -r
. run-level 3 Oct 25 01:32 3 0 S
프롬프트는 unknown으로 나오며 런레벨은 3 으로 올라 옵니다.
제가 어느부분에서 잘못을 했는지요. ^^;
- 신규로 표시
- 북마크
- 구독
- 소거
- RSS 피드 구독
- 강조
- 인쇄
- 부적절한 컨텐트 신고
날짜: 10-25-2005 10:00 PM
날짜: 10-25-2005 10:00 PM
싱글 유저 모드 방법
그리고 single 부팅하면 당연히 호스트 네임데몬의 읽어지지 않기때문에 unknown 으로 나옵니다.
그런데 who -r 했을때 run-level 이 3인게 이상하네요..
mountall 하시고 vi /etc/rc.log 를 확인해보세요~ 정말 3레벨까지 올라온것인지..
- 신규로 표시
- 북마크
- 구독
- 소거
- RSS 피드 구독
- 강조
- 인쇄
- 부적절한 컨텐트 신고
날짜: 10-25-2005 10:00 PM
날짜: 10-25-2005 10:00 PM
싱글 유저 모드 방법
이것은 잘못된 console path의 때문에 발생되는 것입니다.
첨부파일을 열어 확인하시기 바랍니다.
그럼~~
- 신규로 표시
- 북마크
- 구독
- 소거
- RSS 피드 구독
- 강조
- 인쇄
- 부적절한 컨텐트 신고
날짜: 10-25-2005 10:00 PM
날짜: 10-25-2005 10:00 PM
싱글 유저 모드 방법
Main Menu: Enter command or menu > pa
Primary boot path: intscsib.15
0/0/2/1.15
0/0/02/01.f (hex)
Alternate boot path: extscsib.5
0/0/2/0.5
0/0/02/0.5 (hex)
Console path: 0/0/4/0.643
0/0/04/0.283 (hex)
Keyboard path: 0/0/4/0.0
0/0/04/0.0 (hex)
Main Menu: Enter command or menu > pa co 0/0/4/1
ERROR: Unknown Path Type
Main Menu: Enter command or menu > pa co 0/0/4/1.643
ERROR: Unknown Path Type
firmware upgrade는 하지 않았습니다. ^^; 어떻게 하는건지 몰라서요.
재설치를 다시 해봐야 될것 같습니다. (__)(--) 감사 합니다.
- 신규로 표시
- 북마크
- 구독
- 소거
- RSS 피드 구독
- 강조
- 인쇄
- 부적절한 컨텐트 신고
날짜: 10-26-2005 10:00 PM
날짜: 10-26-2005 10:00 PM
싱글 유저 모드 방법
1. (DAT 로- 아래 설명되어있음.)
2. 아래의패치파일로 firmware 를 올릴수있음.
PHSS_29936 - 11.0
PHSS_29937 - 11i
A400/A500/rp24xx
-----------------------------------------------------------
SYSTEM NAME:
DATE: 01/29/2002 TIME: 09:47:14
ALERT LEVEL: 6 = Boot possible, pending failure - action
SOURCE: 8 = I/O
SOURCE DETAIL: 9 = serial SOURCE ID: 0
PROBLEM DETAIL: 3 = functional failure
CALLER ACTIVITY: 1 = test STATUS: 0
CALLER SUBACTIVITY: 4C = implementation dependent
REPORTING ENTITY TYPE: 0 = system firmware REPORTING ID:00
0x00000063890014C0 00000000 00000000 type 0 = Data Field
0x58000863890014C0 00006600 1D092F0E type 11 = Timestamp
-----------------------------------------------------------
위 에러에 대해 패스를 바꿔봐도 안된다면
firmware 를 올려야합니다.(42.09 이상)
VERIFYING FIRMWARE REVISION WITH BOOT CONSOLE HANDLER (BCH)
1. Log on as root, and enter "shutdown -r". This command
will shutdown the Operating System and reboot the system.
2. If AUTOBOOT is on, you will receive the following message:
"Process is starting autoboot process
To discontinue, press any key within 10 seconds."
At this point, press ANY KEY within 10 seconds to
interrupt the booting process.
3. The Main Menu is displayed. A prompt will appear as
"MAIN MENU: Enter command or menu>".
Enter the command "in".
4. A prompt will appear as "Information Menu: Enter Command>"
Enter the command "fv"
The system will respond with the current firmware
revision. If the revision is not revision 43.50
your system will require a Firmware update. Follow the
instructions in the next section, CREATING THE FIRMWARE
UPDATE TAPE.
* * * * * * * * * * CREATING THE FIRMWARE UPDATE TAPE * * * * * * * *
1. Verify the checksum of the file "PF_CHAW4350.frm" using
the "cksum" command. Results of the command should be
equal to "4050135777 3369984 PF_CHAW4350.frm".
2. Use the "dd" command to copy the file "PF_CHAW4350.frm"
to tape, as follows:
dd if=PF_CHAW4350.frm of=/dev/rmt/0m bs=2k
^^^^^^^^^^^
(device path dependent)
NOTE: Blocksize (bs) must be 2k
* * * * * * * * * * * FIRMWARE UPDATE PROCEDURE * * * * * * * * * * *
NOTE: ENSURE YOUR SYSTEM IS FULLY BACKED UP BEFORE
PROCEEDING WITH THIS FIRMWARE UPDATE.
1. Log on as root, and enter "shutdown -r". This command
will shutdown the Operating System and reboot the system.
2. If AUTOBOOT is on, you will receive the following
message:
"Process is starting autoboot process
To discontinue, press any key within 10 seconds."
PRESS ANY KEY WITHIN 10 SECONDS TO INTERRUPT
THE BOOTING PROCESS.
3. Boot from the device that contains the firmware update tape
you just created.
4. Interact with IPL (Y or N)?>
Respond with "N".
A series of messages will be displayed. No user
intervention is required. Proceed to step 5.
5. A message will be displayed as follows:
"F/W file Note:"
"A-Class PDC firmware image, Version 42.50"
"Continue (
Enter "y".
CAUTION: FROM THIS POINT FORWARD, THIS PROCESS CANNOT
BE INTERRUPTED UNTIL COMPLETION. INTERRUPTING
THIS PROCESS WILL CAUSE YOUR SYSTEM TO BE
INOPERATIVE.
6. The update should take approximately two minutes.
After the tape has been read by the update
program, a message will be displayed as follows:
"Firmware downloaded SUCESSFULLY!"
THIS UTILITY WILL NOW RESET THE SYSTEM....
7. The system will automatically reset, and the boot
process will begin. Boot your system with your
normal process.
If there is a problem with your system after the
update, please contact your service representative.
* * * * * * * * * * * * * * END OF UPDATE * * * * * * * * * * * * * *
firmware 는 itrc.hp.com 에서 다운로드 받으실수있습니다.