- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- HPE 9000 and HPE e3000 Servers
- >
- Re: add a new cell to npar
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-09-2006 10:28 PM
тАО10-09-2006 10:28 PM
I have a rp7420 server with one cell board and one npartition. I want to add a new cell to this partition. Igot the following error.What is the problem?
############
Cells exist in the complex that cannot be mixed within a single nPartition. The following groups indicate those cells that are mutually compatible. Do not mix cells from different groups in the same nPartition.
Group 1:
Cell Compatibility: 35024-PA
Firmware Revision: 22.2
Cells:
cab0, cell1
Group 2:
Cell Compatibility: 35040-PA
Firmware Revision: 22.2
Cells:
cab0, cell0
# parmodify -p 0 -a 0:base:y:ri
Warning: The IODC version of cell 1073751848 (35040) and cell 1 (35024) do not match.
Note: It may take a longer time for the partition to boot if
any cell is performing power-on selftest.
# parstatus -C
[Cell]
CPU Memory Use
OK/ (GB) Core On
Hardware Actual Deconf/ OK/ Cell Next Par
Location Usage Max Deconf Connected To Capable Boot Num
========== ============ ======= ========= =================== ======= ==== ===
cab0,cell0 Inactive 8/0/8 16.0/0.0 cab0,bay0,chassis0 no - -
cab0,cell1 Active Core 8/0/8 16.0/0.0 cab0,bay0,chassis1 yes yes 0
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-10-2006 02:50 AM
тАО10-10-2006 02:50 AM
Re: add a new cell to npar
1. could you please check from vfp the cell 0 is in reconfigure reset mode ie BIB mode. I hope the cell's should be in BIB mode during partition confirugaration.
2. check the sysrev output and check both cells and i/o 's are having same firmware.
Thanks and regards
V.Manoharan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-10-2006 04:12 AM
тАО10-10-2006 04:12 AM
Re: add a new cell to npar
looks like you have different firmware versions on the certain components. Please run
MP:CM> sysrev
from the MP prompt and post.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-10-2006 02:50 PM
тАО10-10-2006 02:50 PM
Re: add a new cell to npar
please look at output from sysrev command at MP.
Diferent firmware cellboard at one partition not allowed. but if you want create new partition with cell #1 i think its possible.
Thanks
freddy
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-12-2006 06:35 PM