- Community Home
- >
- Networking
- >
- Legacy
- >
- IP Telephony - NBX
- >
- Re: DIDs on NBX100
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-24-2009 09:50 AM
тАО04-24-2009 09:50 AM
DIDs on NBX100
On an NBX100 with an internal PRI card and the telco is sending 4 digits how do I map the digits the telco is sending direct to extensions thus creating DIDs?
Thanks in advance!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-24-2009 03:29 PM
тАО04-24-2009 03:29 PM
Re: DIDs on NBX100
Every DID will have a PretranslatorEntryCreate entry with a did on the end and a matching PretranslatorOperationCretae as well .
In your dial plan , you will need to go down to the section : pretranslators and you will see 2 areas
PretranslatorEntryCreate ( Telco DID inbound )
PretranslatorOperation Create ( Where to send the call in the NBX )
Every Pretranslator EntryCreate = 1 did
Every PretranslatorOperationCreate = 1 NBX Location as they match . Pretransentry 1 = pretransoperation 1
You need to do a replace action on the PretransOperationCreate , as there are 10 default striplead actions that you do not need , so for the first 10 did's you can modify these to be replace instead of striplead .
Then go into tab to it and find the dialplan/ pretranslator list and find the 5 digit ddi / 4 digit internal pretranslator , and in the list you must select all of your PRI channels and add them into this pretranslator . 3KB's are available on our website @
www.3com.com that explains all these as well .
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-25-2009 11:49 AM
тАО04-25-2009 11:49 AM
Re: DIDs on NBX100
I think I was a bit ambiguous on the original question. There are already a few DIDs in place. I just need to add more. I believe the Telco is sending 4 digits
Is there a simple way to add the new DIDs?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-26-2009 10:02 PM
тАО04-26-2009 10:02 PM
Re: DIDs on NBX100
If you post the pretranslators section of your dial plan should be able to point you in the right location.
Most of the time it's just a matter of copying a previous line and changing the identifier number.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-28-2009 07:30 PM
тАО04-28-2009 07:30 PM