Email Subscription Notifications Suspended Temporarily
We are in the process of making navigation in the Servers and Operating Systems forums simpler and more direct. While doing this, we have to temporarily suspend email notifications for subscriptions. If you are subscribed to one or more discussion boards or blogs in the community, please check them daily to see new content. Notifications will be turned back on in a few days. We apologize for any inconvenience this may cause. Thanks, Warren_Admin
LAN Routing
cancel
Showing results for 
Search instead for 
Did you mean: 

InterVLAN routing not working - New to Procurves

MDU0306
Occasional Visitor

InterVLAN routing not working - New to Procurves

Hello!

 

I'm hoping someone could give me some direction.  Basically my problem boils down to the fact that I can't go anywhere outside of my VLAN 200.  I have a new 2920 Procurve that is connected to a Netgear switch.  The Netgear switch only has the default VLAN 1 setup with an IP of 10.1.1.3.  I have set up VLAN 200 with IP of 10.1.200.1 /24 on the 2920 and have one port Untagged for 200.  This port is 3/2.  The port connected to the Netgear switch is port 3/48.  I can ping our DNS server (10.1.1.125) from the Procurve which is connected to the Netgear switch but when I connect my laptop to port 3/2 (VLAN 200) and manually assign an IP address to my laptop I cannot ping the server.  Here is my config:

 

ip routing

 

vlan 1
   name "DEFAULT_VLAN"
   no untagged 3/1-3/3,3/20,3/47
   untagged
 1/1-1/48,1/A1-1/A2,1/B1-1/B2,2/1-2/48,2/A1-2/A2,2/B1-2/B2,3/4-3/19,3/21-3/46,3/
48,3/A1-3/A2,3/B1-3/B2
   ip address 10.1.1.250 255.255.255.0
   exit

vlan 200
   name "Servers_Printers"
   untagged 3/2
   tagged 3/48
   ip address 10.1.200.1 255.255.255.0
   ip helper-address 10.1.1.125
   exit

interface 3/2 (connected to my laptop)
   untagged vlan 200
   exit

interface 3/48 (connection to Netgear switch)
   tagged vlan 200
   untagged vlan 1
   exit

 

Basically I can't get over to my Netgear switch on VLAN 200.

2 REPLIES
Vince_Whirlwind
Trusted Contributor

Re: InterVLAN routing not working - New to Procurves

Trace the layer-3 path of the packet:

Source: 10.1.200.3

Dest.:10.1.1.3

 

1/ Leaves your laptop, goes to its default gateway, which is the VLAN 200 interface on the 2920, 10.1.200.1

2/ From the VLAN200 interface, the 2920 is direct-connected to the destination subnet, therfore it knows to send out an ARP, find the destination device and switch the packet to it.

3/ The destination device replies by sending its packet to its default gateway. Where is that?

4/ The default gateway will look up its routing table to find the 10.1.200.0 subnet. Can it find it?

MDU0306
Occasional Visitor

Re: InterVLAN routing not working - New to Procurves

I wanted to thank you for your response as it helped me to wrap my head around it and correct my issue.  I had to create a static route on two routers one of which was the Netgear L3 switch that pointed back to that VLAN.  I'm in the middle of implementing a new core which will remove the need for these routers but needed to get the InterVLAN routing functioning in the mean time.  Again, thank you!