- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- MSA Storage
- >
- Re: Restore the default settings HP 8/8 Base SAN S...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2014 05:50 AM - edited тАО01-22-2014 05:53 AM
тАО01-22-2014 05:50 AM - edited тАО01-22-2014 05:53 AM
Restore the default settings HP 8/8 Base SAN Switch
Hello Please help. I have HP 8/8 Base SAN Switch and I want to restore the default settings. Restore the default settings via the web interface failed. I tried to load the new configuration╤О. Everything remains as it was.
Command configdefault didn't help too. everytime all settings remain as it was.
Why its heppend?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2014 05:53 AM
тАО01-22-2014 05:53 AM
Re: Restore the default settings HP 8/8 Base SAN Switch
cfgclear
cfgsave
switchdisable
configDefault
switchenable
NOTE: When using configdefault , all configuration parameters are reset to their default values with the exception of the following:
Ethernet MAC address, IP address, subnetmask, and boot ROM parameters
IP gateway address
License keys
OEM customization
Product ID and Vendor ID
SNMP configuration
iSCSI configuration
System name
Chassis name
World Wide Name
Zoning configuration (includes aliases, zones, and configurations)
Security parameters and policies
User account passwords (includes all user config and all built-in accounts)
Switch PID format
Ethernet Link Mode
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2014 06:04 AM
тАО01-22-2014 06:04 AM
Re: Restore the default settings HP 8/8 Base SAN Switch
cfgclear
cfgsave
switchdisable
configDefault -all
switchenable
Didn't help.
Framework v7.2.0b
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2014 06:08 AM - last edited on тАО02-07-2024 03:23 AM by Sunitha_Mod
тАО01-22-2014 06:08 AM - last edited on тАО02-07-2024 03:23 AM by Sunitha_Mod
Re: Restore the default settings HP 8/8 Base SAN Switch
Did you capture the session?
Please do and post.
See alsohttp://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/kb/docDisplay?javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken&javax.portlet.prp_ba847bafb2a2d782fcbb0710b053ce01=wsrp-navigationalState%3DdocId%253Demr_na-c01747423-1%257CdocLocale%253D%257CcalledBy%253D&javax.portlet.tpst=ba847bafb2a2d782fcbb0710b053ce01&sp4ts.oid=3185340&ac.admitte...
[Moderator edit: Removed the broken link. Please refer to https://support.hpe.com/]
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2014 06:32 AM
тАО01-22-2014 06:32 AM
Re: Restore the default settings HP 8/8 Base SAN Switch
FCSWA5:admin> cfgclear
The Clear All action will clear all Aliases, Zones, FA Zones
and configurations in the Defined configuration.
Run cfgSave to commit the transaction or cfgTransAbort to
cancel the transaction.
Do you really want to clear all configurations? (yes, y, no, n): [no] yes
FCSWA5:admin> cfgsave
WARNING!!!
The changes you are attempting to save will render the
Effective configuration and the Defined configuration
inconsistent. The inconsistency will result in different
Effective Zoning configurations for switches in the fabric if
a zone merge or HA failover happens. To avoid inconsistency
it is recommended to commit the configurations using the
'cfgenable' command.
Do you want to proceed with saving the Defined
zoning configuration only? (yes, y, no, n): [no] yes
"fcswk5" not found
FCSWA5:admin> switchdisable
FCSWA5:admin> configdefault
Executing configdefault...Please wait
Already in Native Mode continuing with configDefault
Committing configuration ... done.
The switch has to be rebooted to allow the changes to take effect.
2014/01/22-14:28:25, [CONF-1031], 618050, FID 128, INFO, FCSWA5, configDefault completed successfully for switch.
FCSWA5:admin> switchenable
WARNING:Switch is Persistently disabled the command will temporarily enable the switch.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2014 06:36 AM
тАО01-22-2014 06:36 AM
Re: Restore the default settings HP 8/8 Base SAN Switch
Did you reboot the switch already?
switchdisable
cfgdisable (hit "y" at prompt)
cfgclear (hit "y" at prompt)
cfgsave (hit "y" at prompt)
configdefault
switchenable
reboot
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2014 06:49 AM - edited тАО01-22-2014 06:53 AM
тАО01-22-2014 06:49 AM - edited тАО01-22-2014 06:53 AM
Re: Restore the default settings HP 8/8 Base SAN Switch
Yes rebooted it.
I want to reset all settings. Name, IP and all the rest. I use the command "configdefault -all".
switchdisable
cfgdisable (hit "y" at prompt)
cfgclear (hit "y" at prompt)
cfgsave (hit "y" at prompt)
configdefault -all
switchenable
reboot
But after a reboot all settings remain, Name, username, password, IP.
Is it possible to do through Shell?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2014 06:59 AM
тАО01-22-2014 06:59 AM
Re: Restore the default settings HP 8/8 Base SAN Switch
"In some cases, the configRemoveAll root command is required for reset. If that is the case,
contact your system administrator",
so try "configremoveall -all"
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2014 07:16 AM - edited тАО01-22-2014 07:16 AM
тАО01-22-2014 07:16 AM - edited тАО01-22-2014 07:16 AM
Re: Restore the default settings HP 8/8 Base SAN Switch
Tried, but he asks
configremove [options] [filename] , because he had not found "configremoveall -all" and "configremove -all" too.
I used configremove -local config,.txt
Then i used "configdefault -all" and reboot. But sittengs remain.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2014 07:36 AM
тАО01-22-2014 07:36 AM
Re: Restore the default settings HP 8/8 Base SAN Switch
It would be helpful to see the session log ... always.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!