- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- Netservers
- >
- Re: Netserver 4LH PIII 700mhz not starting
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-19-2006 04:12 AM - last edited on 12-18-2013 05:33 PM by Lisa198503
02-19-2006 04:12 AM - last edited on 12-18-2013 05:33 PM by Lisa198503
Netserver 4LH PIII 700mhz not starting
Dear all,
I have recently acquired the above and it was working very well. Having tested and run Windows 2003 server successfully on it. I was in the process of placing a clean install onto it, ready for work.
During the reboot of the Windows 2003 setup the server failed to boot. All the lights on the system board and RAM show green.
The event log LCD on the front of the server makes reference to a MMC init 000000007.
I can not get the video, floppy or CD Rom to power up. The Floppy and CD Rom will only power up when they are disconnected from the IDE cables.
The Scsi HDD power up but I am unable to check if they are running correctly.
I have gone through the clear config procedure to no avail and cleaned the RAM connectors
I am a little stuck now and have a server that looks very nice but doesn't do a lot :)
Has any one experienced and overcome this problem or could anyone tell me what MMC 000000007 means?
I would be very grateful for any light you can shed on this problem.
Many thanks
Steve
P.S. This thread has been moved from ProLiant Servers – Netservers to Servers > Netservers. -HP Forum Moderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-18-2013 04:14 AM
12-18-2013 04:14 AM
Re: Netserver 4LH PIII 700mhz not starting
Hello,
I have the same problem on a Netserver LH3. Had the unit switched off and unused for a number of years. Worked fine on last use. Now gives that MMC Init 000000007 error on the console display. Cannot find any infor or get any help from HP about this condition/error.
The CMOS battery went flat and even with a new replacement the server still gives the same error. Noticed the server auxillary power led ON(red) on and the Power good led NOT on. Server just tries to start up all green lights on the PSU unit, Dimm leds and console panel momentatrily then shuts down and all leds off except the auxillary power led that is RED.
Tried replacing the PSU units, NO change
Tried replacing the console display, No change.
Reseated dimm modules No Change
Reseated PII 450 dual CPUs, NO change.
Cleared CMOS No change
Can someone please help as I need to get this server working to retreive some vital files.
Regards John R.