- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- about creation failover group using aggregates con...
Operating System - HP-UX
1754060
Members
3970
Online
108811
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-29-2007 05:45 PM
10-29-2007 05:45 PM
I want to config redundanty network using apa.The application mode like draft in the attachment ,but the aggregation links is 2 other than 3.The following is the command ,is it right ,pls help me correct it.The system version is HP-ux 11iv3 ,is there the configuration information in configuration file ?thanks .
nwmgr -a -A links=2,4 -A mode=MANUAL -c lan900 -S apa
nwmgr -a -A links=900,6 -A mode=LAN_MONITOR -A port_cost=2,3 -c lan901 -S apa
nwmgr -a -A links=2,4 -A mode=MANUAL -c lan900 -S apa
nwmgr -a -A links=900,6 -A mode=LAN_MONITOR -A port_cost=2,3 -c lan901 -S apa
Solved! Go to Solution.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-31-2007 12:50 AM
10-31-2007 12:50 AM
Solution
I don't know the nwmgr syntax well enough yet to tell you offhand, but there's an easy way to "cheat".
Configure the linkagg using smh. Select all the parameters for the linkagg using the puuldowns and check boxes. Then, at the bottom of the screen, click "preview". SMH will show you the command(s) it will run to form the aggregate.
Next, configure the failover group. Same trick, click preview, and the commands for that will be displayed.
Configure the linkagg using smh. Select all the parameters for the linkagg using the puuldowns and check boxes. Then, at the bottom of the screen, click "preview". SMH will show you the command(s) it will run to form the aggregate.
Next, configure the failover group. Same trick, click preview, and the commands for that will be displayed.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP