- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: Queue problem
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-09-2009 06:42 AM
тАО07-09-2009 06:42 AM
Example:
$sh entry [ENTER]
(no response - just blinking cursor)
$pri/que=laserh a.lis [ENTER]
(no response - just blinking cursor)
Tried to print to another printer and have same result
Could someone help troubleshoot?
Thanks,
Amaresh
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-09-2009 08:42 AM
тАО07-09-2009 08:42 AM
Re: Queue problem
http://forums13.itrc.hp.com/service/forums/questionanswer.do?threadId=1350241
?
Your system is badly down-revision with OpenVMS VAX, OpenVMS Alpha or OpenVMS I64 software, you're almost certainly down-revision on patches for V7.2-1, the hardware is likely old and failing, and your system has apparently encountered a low-level problem with the queue manager, the lock manager, or potentially with a disk or disk controller, or with a shared system resource.
If you have a support contract, call HP.
You'll probably end up needing to perform a controlled system crash to save sufficient context on the hang here, then providing the dump to your support organization.
A reboot may or may not clear this.
Whether or not this is hardware or software is not known, and not something that can likely be discerned from ITRC postings.
Whether or not you have a support contract, you'll be asked to upgrade and ECO to current, too. If this problem is not (bad) hardware, then an upgrade to V7.3-2 or to V8.3 (and to current ECO kits) is the best course of action to resolve this.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-09-2009 08:45 AM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-09-2009 10:07 AM
тАО07-09-2009 10:07 AM
Re: Queue problem
start /queue /manager
As various OpenVMS systems have been configured to expect:
start /queue /manager ddcu:[dir]
Check your system startup procedures to see what's used locally. This command is often found in SYS$MANAGER:SYSTARTUP_VMS.COM, though it can be coded elsewhere.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-09-2009 10:23 AM
тАО07-09-2009 10:23 AM
Re: Queue problem
Hakan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-09-2009 08:53 PM
тАО07-09-2009 08:53 PM
Re: Queue problem
Hoff,
This is different VAX server running v6.2
anyway it was a que/manager problem and the root cause was space issue.
Thanks,
Amaresh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-09-2009 08:53 PM
тАО07-09-2009 08:53 PM