- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: Request help with printers
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-07-2007 08:13 AM
тАО03-07-2007 08:13 AM
state of printers with ips? Unfortunately,
the solution will have to be limited to a command procedure(s).
The environment consist of:
Three-node cluster
Compaq AlhaServers GS140
VMS v7.3
Multinet v5.1 EC03
Approx. 500 printers (HP, Datasouth, Xerox, & others)
Thanks for any & all considerations,
PaltiEl
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-07-2007 10:06 AM
тАО03-07-2007 10:06 AM
SolutionToo briefly. "ips"? Inches per second?
Internet Protocol addresses?
It probably depends on the printer. Some,
like my HP LaserJet 4MV ("hplj") respond to
ICMP ECHO packets. (I have HP TCPIP, but I'd
expect MultiNet to have a similar "ping"
command.)
ALP $ show symb ping
PING == "$ SYS$SYSTEM:TCPIP$PING"
ALP $ ping -c 1 -t 5 hplj
PING hplj.antinode.org (10.0.0.50): 56 data bytes
64 bytes from 10.0.0.50: icmp_seq=0 ttl=60 time=4 ms
----hplj.antinode.org PING Statistics----
1 packets transmitted, 1 packets received, 0% packet loss
round-trip (ms) min/avg/max = 4/4/4 ms
ALP $ write sys$output $status
%X00000001
Trying a device ("pha") which is off (powered
off, or off the network):
ALP $ ping -c 1 -t 5 pha
PING pha.antinode.org (10.0.0.101): 56 data bytes
----pha.antinode.org PING Statistics----
1 packets transmitted, 0 packets received, 100% packet loss
%SYSTEM-F-TIMEOUT, device timeout
ALP $ write sys$output $status
%X0000022C
I'd start with that, and see how many live
printers look dead by that criterion. Then
I'd start looking into Telnet (possibly to
unusual ports).
Of course, this doesn't really tell you if
the printer is "on/off", or working, or out
of paper, or warious other things, but it
does show that some communication is
possible.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-07-2007 12:26 PM
тАО03-07-2007 12:26 PM
Re: Request help with printers
Forgetting about the protocol, I would recommend PING to determine if the printer is reachable.
$ MULTINET PING/NUMBER=1/QUIET
then check the value of the symbol $status for SS$_NORMAL (1)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-07-2007 01:58 PM
тАО03-07-2007 01:58 PM
Re: Request help with printers
In parallel, consider standardizing on fewer and newer and network-native printers as part of this project. 500 printers of varying flavors is a substantial investment for parallel stores of toner, etc. And maintenance. And support. (And printers that are not fully network-native should be strongly discouraged.)
Also consider contact with a couple of major printer suppliers, and ask for assistance with this situation. And ask about what it might cost to standardize.
500 printers will catch the attention of many vendors, and you might be surprised what might fall out of an incremental replacement plan.
Stephen Hoffman
HoffmanLabs
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-08-2007 05:51 AM
тАО03-08-2007 05:51 AM
Re: Request help with printers
If "ips" refers to Xerox's DocuPrint controller commands, then your non-DocuPrint printers won't understand.
If the printers are spooled, whatever they tell you or don't tell by direct query means little. The print symbiont controls the printer and the form and devctl modules can change whatever status the printer gives you.
If you're doing dedicated direct printing, then maybe you and your printer can have a meaningful conversation.
Still, if you ask one "are you ready" and it doesn't respond, what will you do? If it says "no", then what? If it says "yes", does that guarantee it will print your report?
If a spooled printer isn't ready or goes off line, usually the queue will stall. If the printer is powered off, what happens depends on how the printer is connected. Direct, print server, network card, whatever. Your report might end up in the bit-bucket or the queue might stall.
The only sure way to tell if a printer is on or off, jammed or whatever, is to look at it. If you can't install video monitors and robots at each location, maybe the same people who see that the printer has paper and ink/toner can be made responsible for the power/ready switch.
So, what is your real goal?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-08-2007 06:54 AM
тАО03-08-2007 06:54 AM
Re: Request help with printers
$ multinet show/stat/snmp=1.2.3.4
Network Interface statistics on Host 139.121.36.18:
HP ETHERNET MULTI-ENVIRONMENT,ROM R.22.01,JETDIRECT,JD95,EEPROM R.25.09,CIDATE 07/24/2003
Name Mtu Network Address Ipkts Ierrs Opkts Oerrs
-------- --- -------- -------------- ------ ----- ------ -----
HP ETHERNE 1500 1.2.3.0 1.2.3.4/24 16229 0 13477 0
HP ETHERNE 32768 Null Address Not an IP interfac 0 0 0 0
$ mu show/snmp=1.2.3.4/mib
Network Interface statistics on Host 139.121.36.18:
HP ETHERNET MULTI-ENVIRONMENT,ROM R.22.01,JETDIRECT,JD95,EEPROM R.25.09,CIDATE 07/24/2003
interfac 0 0 0 0
sysDescr.0 String(89): HP ETHERNET MULTI-ENVIRONMENT,ROM R.22.01,JETDIRECT,
JD95,EEPROM R.25.09,CIDATE 07/24/2003
sysObjectID.0 Object ID: hpNm.3.9.1
sysUpTime.0 Time Ticks: 70625060 (1 week 1 day)
sysContact.0 String(0):
[...etc...]
hpNm.4.3.1.2.0 String(14): ready to print
[...etc...]
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-08-2007 08:06 AM
тАО03-08-2007 08:06 AM
Re: Request help with printers
My use of "ips" actually was meant to abbreviate the plural form for Internet Protocol address (ie 222.100.305.74).
In summary, the requirement to know the printer status stands as a preprequiste to a future application installation. Information concerning the relation between the installation/post installation activity is not known at this time. However, statements from 'lessons learned' by installation engineers highly suggest that printers in the 'on' state could potentially lead to/cause problems.
Again, sincere thanks to all for your time
and professional expertise,
PaltiEl
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-08-2007 10:22 AM
тАО03-08-2007 10:22 AM
Re: Request help with printers
You may want to explore
$ multinet show/conn/snmp=x.x.x.x
which can show any established connections on an snmp-aware printer.