- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: Reset LED in VFP of rx2620
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-01-2010 02:00 AM
тАО07-01-2010 02:00 AM
Reset LED in VFP of rx2620
After booting the first shows green system LED in the VFP, the second shows FLASH RED in the system VFP.
How can I set the system LED in the VFP display back to GREEN without rebooting the server?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-01-2010 02:17 AM
тАО07-01-2010 02:17 AM
Re: Reset LED in VFP of rx2620
A similar topic is discussed in the below thread.
http://forums11.itrc.hp.com/service/forums/questionanswer.do?admit=109447626+1275359612865+28353475&threadId=1309178
May be helpful.
Regards,
Ketan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-01-2010 03:24 AM
тАО07-01-2010 03:24 AM
Re: Reset LED in VFP of rx2620
the reason for the 1. server to shut down and for the 2. to show a FLASH RED in the VFP was the high temperature inside the boxes. Now the temperature is o.k. again and I want to change the system LED from FLASH RED to GREEN without rebooting the server.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-01-2010 05:58 AM
тАО07-01-2010 05:58 AM
Re: Reset LED in VFP of rx2620
Sticker?
No, seriously, does the system have a management processor?
Just connect to the MP port RJ45 / DB25 serial console and read and/or reset the log.
This can be done with the system running and it will clear the LED.
Hope this helps some.
Hein van den Heuvel
HvdH Performance Consulting
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-01-2010 08:00 PM
тАО07-01-2010 08:00 PM
Re: Reset LED in VFP of rx2620
The System LED basically provides information about the system status. If the operation is normal, the LED is green. If there is a system warning, the LED flashes yellow. And if there are any system faults the then this LED flashes RED. Please refer chapter 5 Troubleshooting from the HP Integrity rx2620 Server User Service Guide to fix this issue. Below is the link to above mentioned guide. Hope this helps
http://bizsupport.austin.hp.com/bc/docs/support/SupportManual/c01404139/c01404139.pdf
Regards,
Ketan