- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- Re: dir /ftp fails using tcpware ftp client
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2011 08:30 PM
тАО02-22-2011 08:30 PM
I have a remote VMS servar running FTP service.
No i have two VMS client machine.
Client A is installed TCPIP prod, command -
DIR /FTP REMOTESERVER"USER PASS"::
can be called succesfully.
But on Client B is installed TCPWARE V5.6-2
if run the same dir /ftp command, it got -
%TCPWARE_FTP-E-NOHOSTIVVERB, unknown host name or command verb - check validity and spelling
surely using FTP REMOTESERVER is successful.
So is there any integrating problem with DIR/FTP for tcpware? how to solve?
Thanks a lot
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2011 09:05 PM
тАО02-22-2011 09:05 PM
Re: dir /ftp fails using tcpware ftp client
The online help for the message NOHOSTIVVERB says incorrect host name. Please verify the host name.
%TCPWARE_FTP-E-NOHOSTIVVERB, unknown host name or command verb -
check validity and spelling
Component: FTP-OpenVMS
Meaning: The hostname was entered incorrectly at the FTP host
prompt.
Action: Reenter the correct host name
Regards,
Ketan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2011 09:14 PM
тАО02-22-2011 09:14 PM
Re: dir /ftp fails using tcpware ftp client
Are you able to FTP to the remote node using below command?
$ FTP REMOTESERVER /USERNAME=USER /PASSWORD=PASS
Regards,
Ketan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2011 09:26 PM
тАО02-22-2011 09:26 PM
Re: dir /ftp fails using tcpware ftp client
Are the below logicals defined in the machine?
OPENVMS$FTP,
OPENVMS$FTPDEL,
OPENVMS$FTPDIR
Regards,
Ketan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2011 09:28 PM
тАО02-22-2011 09:28 PM
Re: dir /ftp fails using tcpware ftp client
I tried FTP REMOTESERVER /USER=XX /PASS=XX
It failed with %TCPWARE_FTP-E-NOHOSTIVVERB, unknown host name or command verb - check validity and spelling
it succeeded if only FTP REMOTESERVER, then input username and password after FTP> prompt.
I think Tcpware FTP doesn't allow the syntax of /user /pass.
does that mean Dir /ftp can't use tcpware?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2011 09:34 PM
тАО02-22-2011 09:34 PM
Re: dir /ftp fails using tcpware ftp client
>show log *ftp*
"DECW_FTP_UID" = "TCPWARE:DECW_FTP.UID"
"OPENVMS$FTP" = "TCPWARE:FTP.EXE"
"OPENVMS$FTPDIR" = "TCPWARE:FTP.EXE"
"TCPWARE_FTPD_MBX" = "MBA37:"
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2011 11:36 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2011 05:06 AM
тАО02-23-2011 05:06 AM
Re: dir /ftp fails using tcpware ftp client
with TCPIP Services,
$ Dir/FTP
or to use FTP in a script,
$ ftp
with TCPWARE,
With the Dir & Copy commands, the "/FTP" qualifier will not work.
To use TCPWARE in a script,
$ FTP
Note: Passwords may have to be enclosed with double quotes if they contain lower-case characters or spaces, etc.
Dave.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2011 05:33 AM
тАО02-23-2011 05:33 AM
Re: dir /ftp fails using tcpware ftp client
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-23-2011 07:07 PM
тАО02-23-2011 07:07 PM