Simpler Navigation for Servers and Operating Systems - Please Update Your Bookmarks
Completed: a much simpler Servers and Operating Systems section of the Community. We combined many of the older boards, so you won't have to click through so many levels to get at the information you need. Check the consolidated boards here as many sub-forums are now single boards.
If you have bookmarked forums or discussion boards in Servers and Operating Systems, we suggest you check and update them as needed.
Operating System - Tru64 Unix
cancel
Showing results for 
Search instead for 
Did you mean: 

True64 installation

Sakui
Frequent Advisor

True64 installation


I have a ES 40 Alpha server. i am trying to install an True64 unix but can't pass this line
"Jumping to bootstrap code".

when i boot with the installation CD i can't pass tht line. My console setting is on serial. i have tried other CD ROM but to no avail. My media is in good helath.

P00>>>show device
dkc0.0.0.5.1 DKC0 RZ2DD-LS 0306
dkc100.1.0.5.1 DKC100 RZ2DD-LS 0306
dkc200.2.0.5.1 DKC200 COMPAQ BF03685A35 HPB4
dkc300.3.0.5.1 DKC300 COMPAQ BF03685A35 HPB4
dkc400.4.0.5.1 DKC400 COMPAQ BF03685A35 HPB4
dkc500.5.0.5.1 DKC500 COMPAQ BF03685A35 HPB4
dqa0.0.0.15.0 DQA0 HL-DT-ST CD-ROM GCR-8483 1.02
dva0.0.0.1000.0 DVA0
ewa0.0.0.2002.1 EWA0 00-06-2B-00-CB-EF
ewb0.0.0.6.1 EWB0 08-00-2B-C4-C3-2C
pka0.7.0.2000.1 PKA0 SCSI Bus ID 7
pkb0.7.0.2001.1 PKB0 SCSI Bus ID 7
pkc0.7.0.5.1 PKC0 SCSI Bus ID 7
pkd0.7.0.2.0 PKD0 SCSI Bus ID 7


00>>>show config
hp AlphaServer ES40

Firmware
SRM Console: V7.3-1
ARC Console: v5.71
PALcode: OpenVMS PALcode V1.98-4, Tru64 UNIX PALcode V1.92-5
Serial ROM: V2.22-G
RMC ROM: V1.0
RMC Flash ROM: V2.7

Processors
CPU 0 Alpha EV6 pass 2.5 357 MHz 4MB Bcache
CPU 1 Alpha EV6 pass 2.5 357 MHz 4MB Bcache

Core Logic
Cchip DECchip 21272-CA Rev 9(C4)
Dchip DECchip 21272-DA Rev 2
Pchip 0 DECchip 21272-EA Rev 2
Pchip 1 DECchip 21272-
TIG Rev 10

Memory
Array Size Base Address Intlv Mode
--------- ---------- ---------------- ----------
1 512Mb 0000000000000000 1-Way

512 MB of System Memory

Slot Option Hose 0, Bus 0, PCI
2 NCR 53C895 pkd0.7.0.2.0 SCSI Bus ID 7
3 Radeon 7500 PCI vga0.0.0.3.0
7 Acer Labs M1543C Bridge to Bus 1, ISA
15 Acer Labs M1543C IDE dqa.0.0.15.0
dqb.0.1.15.0
dqa0.0.0.15.0 HL-DT-ST CD-ROM GCR-8483

19 Acer Labs M1543C USB

Option Hose 0, Bus 1, ISA
Floppy dva0.0.0.1000.0

Slot Option Hose 1, Bus 0, PCI
4 DECchip 21152-AA Bridge to Bus 2, PCI
5 NCR 53C895 pkc0.7.0.5.1 SCSI Bus ID 7
dkc0.0.0.5.1 RZ2DD-LS
dkc100.1.0.5.1 RZ2DD-LS
dkc200.2.0.5.1 COMPAQ BF03685A35
dkc300.3.0.5.1 COMPAQ BF03685A35
dkc400.4.0.5.1 COMPAQ BF03685A35
dkc500.5.0.5.1 COMPAQ BF03685A35
6 DE500-BA Network Con ewb0.0.0.6.1 08-00-2B-C4-C3-2C

Slot Option Hose 1, Bus 2, PCI
0 NCR 53C875 pka0.7.0.2000.1 SCSI Bus ID 7
1 NCR 53C875 pkb0.7.0.2001.1 SCSI Bus ID 7
2 DE500-AA Network Con ewa0.0.0.2002.1 00-06-2B-00-CB-EF


00>>>boot dqa
(boot dqa0.0.0.15.0 -flags A)
block 0 of dqa0.0.0.15.0 is a valid boot block
reading 15 blocks from dqa0.0.0.15.0
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 1e00(7680)
initializing HWRPB at 2000
initializing page table at 1ff56000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
P00>>>
P00>>>
3 REPLIES
Steven Schweda
Honored Contributor

Re: True64 installation

> [...] trying to install an True64 unix [...]

Tru64 version? Does it support an ES40, or
do you need an NHD kit?

http://h30097.www3.hp.com/docs/nhd/

> My console setting is on serial.

You're sure?
Sakui
Frequent Advisor

Re: True64 installation


i am using True64 5.1 B.

My console setting is both on serial from the monitor and the hyper terminal.Is it possible to change com2 to be the main console. i need a way out.
Rob Leadbeater
Honored Contributor

Re: True64 installation

Hi,

That doesn't make sense...

What does the output of

P00>>> show console

give you ?

Tru64 5.1B is supported on an ES40 without any need for NHD CDs etc.

Cheers,

Rob

P.S. It's Tru64 NOT True64...