- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: 1785 Drive Array Not configured after motherbo...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-28-2011 01:40 AM - edited тАО06-28-2011 03:07 AM
тАО06-28-2011 01:40 AM - edited тАО06-28-2011 03:07 AM
1785 Drive Array Not configured after motherboard replacement
Hi there,
Here is our story:
We have 2 Proliant DL180 G6 servers.
The one with b110i controller had a pair of 500GB disks in RAID 1 array, and it's motherboard unfortunately died.
While it was being repaired, we've plugged the disks into the other server with p410i controller, and they were recognized and we could use our data on the other server.
Now that the other server is repaired, we want to restore the previous configuration, but the disks are not recognized.When turning the server on, the HDD lights go red-blue-red (upper) - green (lower) and then off/and don't turn on again until server is turned off/on again, and finally after b110i sata raid controller initializaiton we get the message:
1785-Slot 0 Drive Array Not Configured
No Drives Detected
After that, we get the loop of unsuccessful attempts to find a boot device.
Finally, I wanted to configure the Array using ORCA, but I never get to see F8 prompt.
In BIOS (triggered by F9) there is no option to use the array as boot device.
Please help. Is there anything I'm missing or do we have to reinstall or perhaps go for repair again?
Regards
v.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-28-2011 03:14 AM
тАО06-28-2011 03:14 AM
Re: 1785 Drive Array Not configured after motherboard replacement
The HP Smart Array B110i SATA RAID Controller does not support ORCA CL
That explains why there is no F8 option, right?
We've also tried running ACU, but it too only complains about no Drives found.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-28-2011 03:16 AM
тАО06-28-2011 03:16 AM
Re: 1785 Drive Array Not configured after motherboard replacement
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&taskId=110&prodSeriesId=3355734&prodTypeId=12169&objectID=c01647912
Resulted in the same behavior.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-06-2011 09:56 AM
тАО07-06-2011 09:56 AM
Re: 1785 Drive Array Not configured after motherboard replacement
You may need to enable the B110 in the BIOS.
I can't remember exactly where. So you will have to look around, or get the manual.
The disks may be set to SATA, and should be set to RAID (or something like that).
I have seen it once on another DL1xx, a while ago.
Sorry I can't be more specific.
But once you get it set, You will see the B110 during post, with F8 and al the usual stuff.
And you RAID wil be running as before.
BR
/jag
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-07-2011 10:37 PM
тАО07-07-2011 10:37 PM