- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers (ML,DL,SL)
- >
- Re: Problem with 5i+ controller on G3
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-16-2009 12:15 PM
тАО12-16-2009 12:15 PM
Problem with 5i+ controller on G3
I hava a six 150GB SCSI drives in G3 with 5i+ contr. I remove drives and put a new two drives 150 GB 10k and create RAID 1+0. After that I put more two drives 300GB 15k, and now I can not to enter in RAID configuration menu?! I was try a various combination, sometimes I can enter in conf. menu when there is only one drive, but I can not enter in conf. mode when there is more drives.
Thanks on any help.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-16-2009 01:16 PM
тАО12-16-2009 01:16 PM
Re: Problem with 5i+ controller on G3
then replace cache only try now do disk have any leds,
how are you getting to conf mode
first go in bios make sure controller is set to boot , next step go into controller maybe f8 and see does controller see disks s, if not try differant disks ,
do all disks work are they tested ,
how many arrays are working and how many disks in it ,
you said g3 server which model ml dl 350 what is full model ,
are you putting new drives in the old slots ??
This is how we thank in the forum
http://forums11.itrc.hp.com/service/forums/helptips.do?#33
Enjoy:)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-17-2009 05:14 AM
тАО12-17-2009 05:14 AM
Re: Problem with 5i+ controller on G3
Server is DL380 G3.
As I said, server works fine, I remove all six drives and put four NEW drives. I can not enter into controller configuration mode (F8, after ILO).
I think controler has no BBWC, in BIOS is set to boot...
Any other idea?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-17-2009 12:24 PM
тАО12-17-2009 12:24 PM
Re: Problem with 5i+ controller on G3
if this works fine if not
step 2
blade clear nvranm
Clearing the system configuration
To clear the system configuration:
1. Power down the server
3. Remove the access panel look at the diagram on it it will show the position of the maintenace switch( it clears Nv ram)
4. Change position 6 of the system maintenance switch to on.
5. Install the access panel
6. and power up the server blade.
7. Wait for the POST message that prompts you to change the switch setting:
Maintenance switch detected in the "On" position.
Power off the server and turn switch to the "Off" position.
8. Repeat steps 1 through 3.
9. Change position 6 of the system maintenance switch to off.
10. Repeat steps 5 through 7.
now what happens
if still issue get the adu report by starteinf on software smart start cd and post it here i can check it
This is how we thank each other in the forum
http://forums11.itrc.hp.com/service/forums/helptips.do?#33
Enjoy:)
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-18-2009 01:41 PM
тАО12-18-2009 01:41 PM
Re: Problem with 5i+ controller on G3
Anyway, 8 points for your effort :)