- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- MSL6030 Rack Installation Problems
StoreEver Tape Storage
1756575
Members
3720
Online
108848
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-09-2007 11:12 AM
07-09-2007 11:12 AM
MSL6030 Rack Installation Problems
Hello,
I am having trouble racking my MSL6030 in a HP 10,000 series rack. Can anyone help?
This is what happens:
- Installed the rails fine.
- MSL6030 comes with its rails already attached
- extend rails fully
- extend internal rail fully
- slide on tape library until locks
- pushed in blue tabs on both side until slides 3/4 way in and stops.
- Is stuck there unless I go around the back of the rack and lift the tabs on each internal rail to the center. then it keeps sliding in.
- slides all the way in until it hits the bump stops at the back of the rails.
- Unfortunatly I am 2.5-3cm out at the front!!
Any suggestions?? we must have taken the unit in and out 15 times!! I thought mabe you could adjust the rail on the 6030 but the screw holes only match up for one position.
thanks
Peter
I am having trouble racking my MSL6030 in a HP 10,000 series rack. Can anyone help?
This is what happens:
- Installed the rails fine.
- MSL6030 comes with its rails already attached
- extend rails fully
- extend internal rail fully
- slide on tape library until locks
- pushed in blue tabs on both side until slides 3/4 way in and stops.
- Is stuck there unless I go around the back of the rack and lift the tabs on each internal rail to the center. then it keeps sliding in.
- slides all the way in until it hits the bump stops at the back of the rails.
- Unfortunatly I am 2.5-3cm out at the front!!
Any suggestions?? we must have taken the unit in and out 15 times!! I thought mabe you could adjust the rail on the 6030 but the screw holes only match up for one position.
thanks
Peter
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-09-2007 11:34 PM
07-09-2007 11:34 PM
Re: MSL6030 Rack Installation Problems
I recall having the same problem installing one in our lab about 6 months ago. I believe the problem was that one of the rails was off by one square (on the rack) on one side.
I just took a look at ours and the only thing that I needed to do to get the library in was to push in the blue tabs on either side.
One other thing I remember was that we pushed really hard the first time to get it in. I believe that the library rails need to lock onto the bearings of the rack rails. Try lifting the front end up as you push it in.
Hope this helps.
Duane
I just took a look at ours and the only thing that I needed to do to get the library in was to push in the blue tabs on either side.
One other thing I remember was that we pushed really hard the first time to get it in. I believe that the library rails need to lock onto the bearings of the rack rails. Try lifting the front end up as you push it in.
Hope this helps.
Duane
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP