- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Procurve Manager Client TCP/UDP Ports
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-22-2009 03:10 AM
тАО07-22-2009 03:10 AM
I have looked at the documentation and in the forums but if this data is there I cannot see it!
thanks for your time.
Alan
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-22-2009 03:24 AM
тАО07-22-2009 03:24 AM
Re: Procurve Manager Client TCP/UDP Ports
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-22-2009 04:38 PM
тАО07-22-2009 04:38 PM
SolutionI assume you're using PCM 3.0 ...? If so then the following TCP ports must be open between client and server: 3908, 7755, 7770, and 8040.
There are also other ports you will need opened which are dynamically allocated by the PCM server. You can control the ports used rather than allowing dynamic allocation via a configuration file in the PNM/server/config/portmap.txt (assuming PNM is your install directory). The entries in the file that you want to modify for PCM (since you didn't mention its IDM or PMM plugins) look like this by default, where a value of 0 indicates that the port should be dynamically allocated:
DefaultRMI=0
UserMgrSSL=0
DevMgrSSL=0
EventDelivery=0
AccessMgrSSL=0
If you replace these zeros with specific, open TCP port numbers on the server then those ports will be used instead when you bounce the PCM server process after saving the edited file.
Please note that client/server communication through firewalls is not officially supported by ProCurve Manager, although the advice here should work.
Regards,
SVB
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-22-2009 05:21 PM
тАО07-22-2009 05:21 PM
Re: Procurve Manager Client TCP/UDP Ports
Thanks
Alan
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-22-2009 05:24 PM
тАО07-22-2009 05:24 PM
Re: Procurve Manager Client TCP/UDP Ports
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-14-2010 07:09 AM
тАО06-14-2010 07:09 AM
Re: Procurve Manager Client TCP/UDP Ports
I just need to inform that this is absolutely undocumented, and not supported.
And i wouldn't recommend doing this without knowing what you do.