- Community Home
- >
- Networking
- >
- Legacy
- >
- Switches, Hubs, Modems
- >
- Re: cisco ios and catos
Switches, Hubs, and Modems
1754058
Members
4680
Online
108811
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-22-2004 02:25 AM
тАО06-22-2004 02:25 AM
cisco ios and catos
hi,
i have cleared the running configuration of cisco ios in catalyst 4006 series now when i am loging through console i am getting the catos configuration how can i go to the cisco ios so as to reconfigure the switch
thanks
ravi
i have cleared the running configuration of cisco ios in catalyst 4006 series now when i am loging through console i am getting the catos configuration how can i go to the cisco ios so as to reconfigure the switch
thanks
ravi
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-22-2004 04:06 AM
тАО06-22-2004 04:06 AM
Re: cisco ios and catos
You have to download the IOS from the cisco site (which you can only do if you have a maintenance agreement with them and thus an enabled login). Then you do a firmware update using a tftp server. Easier just to use the Cat OS. It's not difficult to figure out. Instead of going to conf t to make a change and saving the changes with a wr me, you just say "set" in front of the command.
What do you want to do? I can probably give you the commands for it.
Ron
What do you want to do? I can probably give you the commands for it.
Ron
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-25-2004 08:42 AM
тАО06-25-2004 08:42 AM
Re: cisco ios and catos
If you just cleared running-config, then your flash should still be working. Did you use a confreg ? If so, re-do confreg 0x2142, by-pass initial set up and you are in.
Otherwise, tell us what command you entered exactly to 'clear' this configuration, and what does the switch displays exctly at login...
J
Otherwise, tell us what command you entered exactly to 'clear' this configuration, and what does the switch displays exctly at login...
J
You can lean only on what resists you...
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP