- Community Home
- >
- Servers and Operating Systems
- >
- HPE BladeSystem
- >
- BladeSystem - General
- >
- Re: BL465c: High Temperature Condition detected by...
BladeSystem - General
1753818
Members
8686
Online
108805
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-14-2008 04:23 PM
04-14-2008 04:23 PM
BL465c: High Temperature Condition detected by Processor
One of the BL465c G1 in a c7000 BladeSystem gives this message after POST:
High Temperature Condition detected by Processor
I found the following article on the web. The OA is 2.10 but the BIOS is an old one (12/02/2006). I tried to upgrade OA to 2.13 and downgrade to 1.30, but neither help. I also upgrade iLO2 to 1.50 but that didn't help, either. The blade was also removed and reinserted a couple of times. Since I couldn't get into any OS, I couldn't update the BIOS of the blade. How can I get pass the POST? Any suggestion?
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c00880424〈=en&cc=us&taskId=115&prodSeriesId=1844065&prodTypeId=329290
Howard
High Temperature Condition detected by Processor
I found the following article on the web. The OA is 2.10 but the BIOS is an old one (12/02/2006). I tried to upgrade OA to 2.13 and downgrade to 1.30, but neither help. I also upgrade iLO2 to 1.50 but that didn't help, either. The blade was also removed and reinserted a couple of times. Since I couldn't get into any OS, I couldn't update the BIOS of the blade. How can I get pass the POST? Any suggestion?
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c00880424〈=en&cc=us&taskId=115&prodSeriesId=1844065&prodTypeId=329290
Howard
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-15-2008 02:13 PM
04-15-2008 02:13 PM
Re: BL465c: High Temperature Condition detected by Processor
I tried to reinsert the blade, reset its configuration using the 6th position on SW1, reboot OA (2.13), but none of these approaches helps. I still see the "High Temperature Condition detected by Processor" error message after POST.
Is there anything else I can do?
Is there anything else I can do?
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP