Port mapping on Pass-Thru Module port has changed

[Shrek71]

Hi

Does anybody have an idea how to change the port mappings the pass through module "sees"

Until recently the pass through module reported the physical mac address of the network cards it mapped to

Now, it's mapping to Ethernet FlexNIC MZ2 2-a (previously it was port1 or port 2)

I'd like to change this back.

Screen shot attached shows a mix of the old and the new settings...

Ideally I want to disable the "new" mappings and go back to using the physical ports.

Thanks in advance

[scharchouf]

what you want to do exactly?

[Shrek71]

Something changed in my configuration recently and I don't know what. I didn't intentionally change anything however note the MAC addresses of the HP Flex-10 10Gb 2P 530M network card.

Take a look at the following output:

Server Blade #1 Information:

......

Mezzanine 2: HP Flex-10 10Gb 2-port 530M Adapter
Port 1: 2c:76:8a:59:66:b8
Port 2: 2c:76:8a:59:66:bc

......

Server Blade #2 Information:

......

Mezzanine 2: HP Flex-10 10Gb 2-port 530M Adapter
Ethernet FlexNIC MZ2:1-a 00:17:A4:77:00:0C
Ethernet FlexNIC MZ2:2-a 00:17:A4:77:00:0E

......

In server 1, the MAC addresses look like the physical address of the NICs

In server 2, the MAC address look like they were allocated by the VC module

The servers were configured to use the physical addresses.

If using a VC assigned MAC is the preferred way of doing it, I may move that way however right now I'm to figure out what's happened.

Kind regards

Full output:

c7k1Active> show server info 1

Server Blade #1 Information:
Type: Server Blade
Manufacturer: HP
Product Name: ProLiant BL465c Gen8
Part Number: 634975-B21
System Board Spare Part Number: 683821-001
Serial Number: CZ324415MC
UUID: 39343336-3537-5A43-3332-343431354D43
Server Name: host is unnamed
Asset Tag: [Unknown]
ROM Version: A26 06/09/2013

CPU 1: AMD Opteron(TM) Processor 6272 (16 cores)
CPU 2: AMD Opteron(TM) Processor 6272 (16 cores)
Memory: 131072 MB

FLB Adapter 1: HP Flex-10 10Gb 2-port 530FLB Adapter
Ethernet FlexNIC (NIC 1) LOM1:1-a 00:17:A4:77:00:00
Ethernet FlexNIC (NIC 3) LOM1:1-b 00:17:A4:77:00:28
Ethernet FlexNIC (NIC 5) LOM1:1-c B4:B5:2F:6D:5C:52
Ethernet FlexNIC (NIC 7) LOM1:1-d B4:B5:2F:6D:5C:53
Ethernet FlexNIC (NIC 2) LOM1:2-a 00:17:A4:77:00:02
Ethernet FlexNIC (NIC 4) LOM1:2-b 00:17:A4:77:00:2A
Ethernet FlexNIC (NIC 6) LOM1:2-c B4:B5:2F:6D:5C:56
Ethernet FlexNIC (NIC 8) LOM1:2-d B4:B5:2F:6D:5C:57

Mezzanine 2: HP Flex-10 10Gb 2-port 530M Adapter
Port 1: 2c:76:8a:59:66:b8
Port 2: 2c:76:8a:59:66:bc

Management Processor Information:
Type: iLO4
Name: ILOCZ324415MC
Firmware Version: 1.32 Nov 05 2013
IP Address: 83.220.202.135
MAC Address: AC:16:2D:A9:78:9D
Power Management Controller Version: 3.0
VLAN ID: 2

c7k1Active> show server info 2

Server Blade #2 Information:
Type: Server Blade
Manufacturer: HP
Product Name: ProLiant BL465c Gen8
Part Number: 634975-B21
System Board Spare Part Number: 683821-001
Serial Number: CZ324415ME
UUID: 39343336-3537-5A43-3332-343431354D45
Server Name: c7k1hv2.flexecloud.com
Asset Tag: [Unknown]
ROM Version: A26 06/09/2013

CPU 1: AMD Opteron(TM) Processor 6272 (16 cores)
CPU 2: AMD Opteron(TM) Processor 6272 (16 cores)
Memory: 131072 MB

FLB Adapter 1: HP Flex-10 10Gb 2-port 530FLB Adapter
Ethernet FlexNIC (NIC 1) LOM1:1-a 00:17:A4:77:00:08
Ethernet FlexNIC (NIC 3) LOM1:1-b 00:17:A4:77:00:10
Ethernet FlexNIC (NIC 5) LOM1:1-c 00:17:A4:77:00:20
Ethernet FlexNIC (NIC 7) LOM1:1-d B4:B5:2F:6D:EC:53
Ethernet FlexNIC (NIC 2) LOM1:2-a 00:17:A4:77:00:0A
Ethernet FlexNIC (NIC 4) LOM1:2-b 00:17:A4:77:00:12
Ethernet FlexNIC (NIC 6) LOM1:2-c 00:17:A4:77:00:22
Ethernet FlexNIC (NIC 8) LOM1:2-d B4:B5:2F:6D:EC:57

Mezzanine 2: HP Flex-10 10Gb 2-port 530M Adapter
Ethernet FlexNIC MZ2:1-a 00:17:A4:77:00:0C
Ethernet FlexNIC MZ2:2-a 00:17:A4:77:00:0E

Management Processor Information:
Type: iLO4
Name: ILOCZ324415ME
Firmware Version: 1.32 Nov 05 2013
IP Address: 83.220.202.136
MAC Address: AC:16:2D:A9:78:86
Power Management Controller Version: 3.0
VLAN ID: 2

[scharchouf]

Ok I see that ther's some confuse Information, please send me a ShowAll and I will verify the configuration :)

[Shrek71]

Just updating this ticket with the problem and the solution.

This turned out to be a bug that is being investigated.

Somehow the VC module in the chassis managed to allocate MAC addresses to the Mezzanine card that mapped to the pass-thru module!  This happened for 6 of the 16 servers. Powering down/up the servers didn't resolve the issue. The following sequence worked for me.

1) Power down the blade

2) Un-assign the VC profile

3) Assign the VC profile

4) From the OA CLI, reset server X

5) Power on the blade

Verify the port mappings.

Hope this helps somebody else.