HPE GreenLake Administration
- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- 5920AF ipv6 PBR wont apply, claims not enough reso...
Comware Based
1833777
Members
2311
Online
110063
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Forums
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-19-2020 05:29 PM
01-19-2020 05:29 PM
Hello,
I need to implement PBR for ipv6 on HPE 5920AF switch and when I attempt to apply it to interface, I get error
[switch-Vlan-interface2]ipv6 policy-based-route PBR-ipv6
Not enough resources to complete the operation, slot 1.
but checking reqources, there should be enough of them
<switch>display qos-acl resource
Interfaces: XGE1/0/1 to XGE1/0/24
---------------------------------------------------------------------
Type Total Reserved Configured Remaining Usage
---------------------------------------------------------------------
VFP ACL 1024 256 0 768 25%
IFP ACL 2048 1024 749 275 86%
IFP Meter 1024 512 0 512 50%
IFP Counter 1024 512 0 512 50%
EFP ACL 1024 0 0 1024 0%
EFP Meter 512 0 0 512 0%
EFP Counter 512 0 0 512 0%
Here is some more info from the switch
<switch>dis acl ipv6 all
Advanced IPv6 ACL 3020, named -none-, 1 rule,
ipv6 PBR bypass
ACL's step is 10
rule 10 permit ipv6 destination 2A00:0C00::/29
Advanced IPv6 ACL 3021, named -none-, 1 rule,
ipv6 PBR
ACL's step is 10
rule 10 permit ipv6 source 2A00:0C04::/36
<switch>dis ipv6 policy-based-route
Policy name: PBR-ipv6
node 10 deny:
if-match acl 3020
node 20 permit:
if-match acl 3021
apply next-hop 2A00:0C00:1::1
<l3sw-mwifi-5920>dis cur int vlan2
interface Vlan-interface2
ip address xxx
ip address xxx sub
ip policy-based-route xxx
ipv6 address FE80::1 link-local
ipv6 address 2A00:0C00:1:2::1/64
<switch>dis version
HPE Comware Software, Version 7.1.045, Release 2432P05
Copyright (c) 2010-2017 Hewlett Packard Enterprise Development LP
HPE 5920AF-24XG Switch uptime is 8 weeks, 1 day, 4 hours, 18 minutes
Last reboot reason : Cold reboot
Wondering if there is maybe something I am doing wrong, or I need to allocate manually resources to ipv6 rules? I know there is one patch newer firmware, but I checked release notes and dont see any mentioning of ipv6 PBR.
Solved! Go to Solution.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-20-2020 04:03 PM
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
Company
Events and news
Customer resources
© Copyright 2025 Hewlett Packard Enterprise Development LP