Comware Based
cancel
Showing results for 
Search instead for 
Did you mean: 

HP 5130 - replace fan

 
Highlighted
Occasional Visitor

HP 5130 - replace fan

Hi,

i have to replace one of the fan on my HP 5130-48. The fails fan has code "Hpe X722 port to power fan tray 5060-0174" and it has red levers in its back.

The replace parts has blue levers, code is "HPE X722 BF fan tray".

The problem is that when i put the new one it doesn't recognize "fan prefer direction" commands: after a few seconds the flow remains unchanged and the switch tells to check air flow-direction.

My dubt is that the new spare parts in not exactly like the broken fan...

Any ideas?

 

3 REPLIES 3
Highlighted
HPE Pro

Re: HP 5130 - replace fan

Hi,

Can you please share the exact command applied to change the flow direction.

For you reference:

e.g
fan prefer-direction
Use fan prefer-direction to configure the preferred airflow direction.

Use undo fan prefer-direction to restore the default.

Syntax
fan prefer-direction slot slot-number { power-to-port | port-to-power }

undo fan prefer-direction slot slot-number

If issue remains after applying above command then share below output and also share the old fan and new fan product/part number.

display device manuinfo fan
display fan
display version

 

Thanks!

I am an HPE Employee

Accept or Kudo

Highlighted
Occasional Visitor

Re: HP 5130 - replace fan

Hi,

during a test I tried to disassemble it and now it works. I don't know why, maybe it would have been a faulty contact.

Slot 1:
Fan 1:
State : Normal
Airflow Direction: Port-to-power
Prefer Airflow Direction: Port-to-power
Fan 2:
State : Normal
Airflow Direction: Port-to-power
Prefer Airflow Direction: Port-to-power

Slot 2:
Fan 1:   -->> It is the "Faulty" fan
State : Normal
Airflow Direction: Port-to-power
Prefer Airflow Direction: Port-to-power
Fan 2:
State : Normal
Airflow Direction: Port-to-power
Prefer Airflow Direction: Port-to-power

Display version:

HPE Comware Software, Version 7.1.045, Release 1111P01
Copyright (c) 2010-2015 Hewlett Packard Enterprise Development LP
HPE 5130 48G 4SFP+ 1-slot HI Switch JH324A uptime is 22 weeks, 4 days, 6 hours, 10 minutes
Last reboot reason : Cold reboot

Boot image: flash:/5130hi-cmw710-boot-r1111p01.bin
Boot image version: 7.1.045, Release 1111P01
Compiled May 13 2015 15:54:04
System image: flash:/5130hi-cmw710-system-r1111p01.bin
System image version: 7.1.045, Release 1111P01
Compiled May 13 2015 15:54:04


Slot 1:
Uptime is 22 weeks,4 days,6 hours,11 minutes
HPE 5130 48G 4SFP+ 1-slot HI Switch JH324A with 2 Processors
BOARD TYPE: 5130 48G 4SFP+ 1-slot HI Switch
DRAM: 1984M bytes
FLASH: 512M bytes
PCB 1 Version: VER.A
Bootrom Version: 111
CPLD 1 Version: 003
Release Version: HPE 5130 48G 4SFP+ 1-slot HI Switch JH324A-1111P01
Patch Version : None
Reboot Cause : ColdReboot
[SubSlot 0] 48GE+4SFP Plus

Slot 2:
Uptime is 1 week,0 days,6 hours,55 minutes
HPE 5130 48G 4SFP+ 1-slot HI Switch JH324A with 2 Processors
BOARD TYPE: 5130 48G 4SFP+ 1-slot HI Switch
DRAM: 1984M bytes
FLASH: 512M bytes
PCB 1 Version: VER.A
Bootrom Version: 111
CPLD 1 Version: 003
Release Version: HPE 5130 48G 4SFP+ 1-slot HI Switch JH324A-1111P01
Patch Version : None
Reboot Cause : ColdReboot
[SubSlot 0] 48GE+4SFP Plus

Thanks for your support!

 

Highlighted
HPE Pro

Re: HP 5130 - replace fan

Hi,

Now it seems FAN 2 state is 'Normal;'.

It might be because of  a faulty contact..

Also the deivce is running on very old software and I will advise you to upgrade it to latest.

Thanks!

I am an HPE Employee

Accept or Kudo