- Community Home
- >
- Networking
- >
- Switching and Routing
- >
- Comware Based
- >
- Re: Hybrid Ports going into blocked state when lld...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2021 09:44 AM - last edited on тАО09-07-2021 08:39 PM by support_s
тАО09-07-2021 09:44 AM - last edited on тАО09-07-2021 08:39 PM by support_s
Hybrid Ports going into blocked state when lldp global is enabled
Hi there,
I have Hybrid ports set up , with both voice and data..When I turn on LLDP globally thos ports go int blocked state. I have looked at the logs and a little weird "port hybrid vlan 1 in view Gigabit etc faailed to be matched". Has anyone come accross this before, also I do have undo vlan 1 on all ports etc
Regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2021 10:10 AM - edited тАО09-07-2021 10:11 AM
тАО09-07-2021 10:10 AM - edited тАО09-07-2021 10:11 AM
Re: Hybrid Ports going into blocked state when lldp global is enabled
Hello @prodigy811 ,
Can you share the softwre version and device mode and config used for that port?
Also share 'display logbuffer reverse' and also share spanning tree status on port?
Thanks!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2021 11:08 AM
тАО09-07-2021 11:08 AM
Re: Hybrid Ports going into blocked state when lldp global is enabled
Hi there,
Many thanks for response. The Model is a 5510 48G PoE+ 4SFP+ HI 1-slot Switch, version HPE Comware Software, Version 7.1.045, Release 1122P02
To note, this switch was installed to replace a faulty cisco switch. Hence trying to enable LLDP globally
Port config is;
port link-mode bridge
port link-type hybrid
undo port hybrid vlan 1
port hybrid vlan 31 tagged
port hybrid vlan 2 untagged
port hybrid pvid vlan 2
voice-vlan qos trust
undo voice-vlan mode auto
voice-vlan 31 enable
shutdown
stp edged-port
lldp compliance admin-status cdp txrx
lldp tlv-enable dot1-tlv protocol-vlan-id 31
lldp tlv-enable med-tlv network-policy 31
poe enable
Section in logbuffer;
%Sep 7 17:20:00:624 2021 switch SHELL/4/SHELL_CMD_MATCHFAIL: -User=**-IPAddr=**; Command port hybrid vlan 1 in view GigabitEthernet1/0/3 failed to be matched.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2021 11:44 AM
тАО09-07-2021 11:44 AM
Re: Hybrid Ports going into blocked state when lldp global is enabled
Hello @prodigy811 ,
Config looks correct however device is running on very old software version and I will advise you to upgrade it to latest version.
Can you confirm if this interface is 'shutdown' or you tried to 'unshutdown' as well?
Also can you configure below comands as well:
lldp global enable
lldp compliance cdp
Thanks!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2021 12:44 PM - edited тАО09-07-2021 12:45 PM
тАО09-07-2021 12:44 PM - edited тАО09-07-2021 12:45 PM
Re: Hybrid Ports going into blocked state when lldp global is enabled
Hi @prodigy811 !
Could you reproduce the issue and post here:
1. Output from the following commands:
display stp interface <blocked_port_number>
display stp abnormal-port
display stp down-port
2. Log messages (display logbuffer) relevant to the port blocking?
One question - does it happen only on ports where you have IP phones and PCs connected? What if you connect a PC directly to such a hybrid port? Will it be blocked as well?
And I agree with akg7, the idea about firmware upgrade makes a lot of sense since your current version is from initial releases and is about 4 years old
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-07-2021 12:56 PM
тАО09-07-2021 12:56 PM
Re: Hybrid Ports going into blocked state when lldp global is enabled
Hi all,
Many thanks for your replies and recommendations.. To answer your question Ivan, I cannot be 100% sure but it seems that it only happens to ports where both pc and phone are connected. Ill need to arrange some more downtime to run these test again. Once I do ill reply here. thanks again all for your help
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-08-2021 01:11 AM - edited тАО09-08-2021 01:12 AM
тАО09-08-2021 01:11 AM - edited тАО09-08-2021 01:12 AM
Re: Hybrid Ports going into blocked state when lldp global is enabled
If STP blocks such ports, it is probably because it gets STP BPDUs back. Since it happens only (as for now) on ports with VoIP phones and PCs behind them, maybe there is an incorrect forwarding between vlan 31 and vlan 2 inside the phone, between its two Ethernet interfaces, so multicast and broadcast traffic from one vlan leaks to another and thus a loop is created. And it's not clear why it happens only when LLDP is enabled, maybe LLDP messages are not compliant to CDP or phones do not recognize them and instead of terminating those on the phone itself, the phone treats it as a multicast and forwards. And since the phone didn't recognize CDP message, it doesn't set its VLAN configuration correctly and that's how this leak between vlans happen.
It is just a hypothesis, don't take it as a root cause. Since you are going to plan a downtime, upgrade the switch, implement configuration changes as per akg7's suggestions (enable CDP compliance for LLDP globally) and test. As far as I remember Cisco phones, you can check VLAN configuration of its both Ethernet interfaces (switch-facing and PC-facing) from the phone itself - ensure that VLAN config is per your expectations - VoIP traffic tagged in vlan 31 and PC is in untagged vlan 2.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-09-2021 03:57 AM
тАО09-09-2021 03:57 AM
Re: Hybrid Ports going into blocked state when lldp global is enabled
Hi all,
Just an FYI, completed upgrade succesfully and put LLDP Compliance CDP and LLDP Global Enable commands in and all looked good, no mac addresses have been blocked. However the phones lost there IP addresses. The display mac address only saw vlan 2. The long and short of it I took out "undo voice vlan mode auto" in the port config and that worked.
So my question is; iitially the issue was LLDP Global command caused issue and mac addresses where then blocked. The phones where getting there IP address. When I configured " lldp compliance cdp & lldp global enable it must have caused the issue as they where the only changes. It was fixed by removing the "undo voice vlan mode auto" config.
If you have any theories why that was the fix id be grateful for you input.
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-21-2021 01:36 AM
тАО09-21-2021 01:36 AM
Re: Hybrid Ports going into blocked state when lldp global is enabled
Hi all,
Any ideas on my above questions?