- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- Disk Enclosures
- >
- Re: Error Message in MSA1000
Disk Enclosures
1748201
Members
2915
Online
108759
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-07-2008 10:58 PM
02-07-2008 10:58 PM
Error Message in MSA1000
Hi All,
One of my cu have a MSA1000 with two controller in Active/Passive mode.Active controller is showing an error "30 I2C READ FAILURE CASHE DIMM PIC 0 ". I had reveived a cashe module with 256MB. After replaced the part issue was same. I have been chacked with other two cashe module from my passive controller but isssue was same.
Could someone tell me can i inter change the controller or not. if i do it than my configration will same or it will be erase.
clustering is configuered with 4 dl380 g5 server and o/s is suse linux.
Could someone tell me what is the acctule issue according this error.
thaks & regards
rakesh kumar
m- 91-9958691040/9873499319
One of my cu have a MSA1000 with two controller in Active/Passive mode.Active controller is showing an error "30 I2C READ FAILURE CASHE DIMM PIC 0 ". I had reveived a cashe module with 256MB. After replaced the part issue was same. I have been chacked with other two cashe module from my passive controller but isssue was same.
Could someone tell me can i inter change the controller or not. if i do it than my configration will same or it will be erase.
clustering is configuered with 4 dl380 g5 server and o/s is suse linux.
Could someone tell me what is the acctule issue according this error.
thaks & regards
rakesh kumar
m- 91-9958691040/9873499319
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-07-2008 11:27 PM
02-07-2008 11:27 PM
Re: Error Message in MSA1000
I2C is Inter Integrated Circuit bus, it's the one intercommunicating the chips on the controller. This looks like a failed chip somewhere on the controller (PIC likely refers to Programmable Interrupt Controller)
The information is on the disks, you can disable controller (through serial port), remove it and replace it.
The information is on the disks, you can disable controller (through serial port), remove it and replace it.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP